Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Select the region in which the wireless interface will operate. 5. Leave the Wireless mode at the default setting of 130 Mbps. This mode is backward compatible with 802.11b and 802.11g wireless adapters. Configuring Your Wireless Network 6. Click Apply to save your changes. If you are configuring the wireless-N gigabit modem router from a wireless computer and you change the wireless-N gigabit modem router’s SSID, channel, or security settings, you will lose your wireless connection when you click Apply. You must then change the wireless settings of your computer to match the wireless-N gigabit modem router’s new settings. 7. Configure and test your computers for wireless connectivity. Program the wireless adapter of your computers to have the same wireless network name (SSID) as the wireless-N modem router. Check that they have a wireless link and are able to obtain an IP address by DHCP from the wireless-N gigabit modem router. Your wireless-N modem router is now configured to provide Internet access for your network. Your wireless-N modem router automatically connects to the Internet when one of your computers requires access. It is not necessary to run a dialer or login application such as Dial-Up Networking to connect, log in, or disconnect. These functions are performed automatically by the wireless-N modem router as needed. To access the Internet from any computer connected to your wireless-N modem router, launch a browser such as Microsoft Internet Explorer or Firefox. You should see the wireless-N modem router’s Internet LED blink, indicating communication to the ISP. The browser should begin to display a Web page. Configuring Your Wireless Network Troubleshooting This chapter gives information about troubleshooting your wireless-N modem router. After each problem description, instructions are provided to help you diagnose and solve the problem. For the common problems listed, go to the section indicated. • Is the router on? Go to “Basic Functioning” on page 28. • Have I connected the router correctly? Go to “Troubleshooting the Web Configuration Interface” on page 30. • I cannot access the router’s configuration with my browser. Go to “Troubleshooting Internet Browsing” on page 33. • I have configured the router but I can’t access the Internet. Go to “Troubleshooting the ISP Connection” on page 31. • I cannot remember the router’s configuration password. Go to “Default Configuration” on page 37. • I want to clear the configuration and start over again. Go to “Restoring the Default Configuration and Password” on page 35. Basic Functioning After you turn on power to the router, the following sequence of events should occur: 1. When power is first applied, verify that the Power LED is on (see “Hardware Features” on page 3 for an illustration and explanation of the LEDs). 2. After approximately 10 seconds, verify that: a. The LAN port LEDs are lit for any local ports that are connected. b. The ADSL Internet port LED is lit. Troubleshooting If a port’s LED is lit, a link has been established to the connected device. If a LAN port is connected to a 1000 Mbps device, verify that the port’s LED is green. If the port is 10/100 Mbps, the LED will be amber. If any of these conditions does not occur, refer to the appropriate following section. Power LED Not On If the Power and other LEDs are off when your router is turned on: • Make sure that the power cord is properly connected to your router and that the power supply adapter is properly connected to a functioning power outlet. • Check that you are using the power adapter supplied by NETGEAR for this product. If the error persists, you have a hardware problem and should contact technical support. Power LED is Red When the router is turned on, it performs a power-on self test. If the Power LED turns red after a few seconds or at any other time during normal operation, there is a fault within the router. The power LED also turns red when you depress the factory default reset push buttons, and blinks red 3 times when that button is released. However, in this case, the wireless-N modem router is working normally. If the power LED turns red to indicate a router fault: • Cycle the power to see if the router recovers. If the power LED is still red one minute after power up: • Cycle the power to see if the router recovers. • Clear the router’s configuration to factory defaults. This will set the router’s IP address to 192.168.0.1. This procedure is explained in “Default Configuration” on page 37. If the error persists, you might have a hardware problem and should contact technical support. LAN or Internet Port LEDs Not On If either the LAN LEDs or ADSL Internet LED do not light when the Ethernet connection is made, check the following: • Make sure that the Ethernet cable connections are secure at the router and at the hub or workstation. • Make sure that power is turned on to the connected hub or workstation. Troubleshooting • Be sure you are using the correct cable...