Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Fotos und technische Daten NETGEAR WNCE3001 |
Anleitung Zusammenfassung
When the Step 1: Connect the WNCE3001 wireless connection has been established, the LED changes color to indicate the quality of the connection—solid green, solid amber, or solid red. Check “Adapter LED Activity” on the reverse side for more information about what these colors mean. to your TV, XBox, or Blu-ray player using the Ethernet cable (included) and one of the power connection options. For more information on power-up methods, see “Power Connection Options” on the reverse side. WNCE3001 is blinking green. Push the WPS button on the WNCE3001. The LED will blink amber and green, showing that the WPS is running. Step 4: Congratulations! Your installation is complete. What is WPS? If you have a NETGEAR router, this feature is called Push ‘N’ Connect. Look for the or symbols on the router to make sure the NETGEAR router supports WPS. For non-NETGEAR routers, please refer to the user manual to determine if the router supports WPS. Once you know whether your router supports WPS, choose the appropriate installation method below. WPS (Wi-Fi Protected Setup) is a simple and secured way to connect a device to an existing network. Installation without WPS Step 1: On the computer you will use to install the WNCE3001, disconnect its wireless connection to the router and/or remove the Ethernet cable currently connected to the computer. You may restore the connection after the WNCE3001 installation is complete. Step 2: Connect the WNCE3001 to your computer, using the Ethernet cable (included) and one of the power connection options. For more information on power-up methods, see “Power Connection Options” on the reverse side. Step 3: Wait until the LED is blinking green. Make sure the computer gets the IP address. Then, open you Internet browser and it will automatically take you to the setup page. (If not, manually type as the browser address.) Follow the instructions on the setup page, then return to this guide and continue to Step 4. Step 4: Disconnect the Ethernet and USB cables from your computer. Step 5: Connect the WNCE3001 to your TV, Box, or Blu-ray player. If your device does not have a USB port, see “Power Connection Options” on the reverse side. button WPS NOTE: Make sure you go through the connection settings on your TV, XBox, or Blu-ray player after the WNCE3001 is configured and connected. If asked for the type of connection, make sure WIRED is selected. 7. Why is the LED solid red during power on? Power Connection Options FAQ It is likely that the USB port you are connected to does not provide enough power for You can power on your WNCE3001 using either of these methods: • Connect the WNCE3001 to a wall outlet with the included power adapter. Power adapter • Connect the WNCE3001 to any USB port using the included USB power cable: USB power cable WPS Process Here is the sequence of events when you press the WPS button to establish your wireless connection: • When WPS is in process, the LED turns green for 500 milliseconds, then off for 500 milliseconds, then turns amber for 500 milliseconds, then off for 500 milliseconds, continuously. • When WPS is done, the LED displays the link rate quality: solid green, solid amber, or solid red. Note: In the event of a WPS failure, the LED switches between green and red at intervals of 0.5 seconds. June 2011 1. Which power connection options should I choose? Many consumer electronics devices have Ethernet and USB ports in close proximity. Using the USB power cable option allows you to free up one power outlet that can be used for something else. Even if the device to which you connect the WNCE3001 does not have a free USB port, as long as there is a free USB port on a neighboring device within cable length of the WNCE3001, and that device can be turned on when you use the WNCE3001, you can plug the USB power cable into the neighboring device. Note that some USB ports on consumer electronic devices may not be capable or providing the power that the WNCE3001 requires. In such cases, the WNCE3001 may reset itself or turn itself off. When this happens, please use the WNCE3001 power adapter when powering up the WNCE3001. 2. When setting up the WNCE3001 without using WPS, does the computer have to be on DHCP for the installation to work? Yes. 3. Why am I getting the error “Connection was not established to the selected network.”? There are a few reasons for this. First, you may have entered the incorrect network name or key. Make sure it is typed in correctly by clicking Cancel and re-typing the name and key. Second, the router may have stopped broadcasting. Make sure the router that is broadcasting your wireless network is still turned on and there is a clear line of sight between the WNCE3001 and the router. If possible, move the WNCE3001 closer to the router and click Try Again. If after repeated attempts to connect, you are still seeing this message, you may need to upgrade your router to one that provides greater wireless range, or purchas...