Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
The NETGEAR WG602 Wireless Access Point connects to all existing 802.11b wireless networks and supports new clients based on the forthcoming ultra-fast 802.11g standard at 54 Mbps all in the same 2.4 GHz radio frequency range. Package Contents This package should contain: • WG602 Wireless Access Point • Power adapter and cord (12VDC, 1.2A) • NETGEAR’s WG602 Resource CD • WG602 User's Guide • Straight-through Category 5 Ethernet cable—5 feet (1.52 m) • Support information card • Warranty card Model WG602 Resource CD, User's guide, Support information card, Warranty card Power adapter Category 5 100 Mbps Ethernet cable Stand WG602 54 Mbps Wireless Access Point 1 You can refer to the Support information card for the telephone number of customer support in your area. You should keep the Support information card, along with the original packing materials, and use the packing materials to repack the WG602 54 Mbps Wireless Access Point if you need to return it for repair. To qualify for product updates and product warranty registrations, we encourage you to register on the NETGEAR’s web page at: System Requirements Before installing the WG602, your system should meet the following requirements: • A Cable/DSL Router with multiple 10/100 Mbps Ethernet Ports or a 10/100 Mbps Local Area Network device such as a hub or switch. Note: The WG602 will need to be connected to a router, switch, or hub as shown in the picture below. • A Category 5 UTP straight-through Ethernet cable with the RJ-45 connector (included in this package or one similar to it). • An A/C power outlet (100-240 V, 50-60 HZ). • A Web browser for configuration, such as Microsoft® Internet Explorer 5.0 or above, or Netscape Navigator® 4.78 or a later version. • One computer with TCP/IP protocol installed. • Other 802.11b or 802.11g-compliant devices, such as the NETGEAR WAB501 Dual Band Wireless PC Card or WG511 54 Mbps Wireless PC Card. Cable or DSL modem Cable/DSL Router WG602 54 Mbps Wireless Access Point 12 VDC 1.2A + WG511 54 Mbps Wireless PC Card in a Notebook computer W CCard 32-bitCardBusWG511 WG602 Wireless Access Point Front Panel The WG602 Wireless Access Point provides these status lights: Power, Ethernet, and Wireless. Power Ethernet Wireless This chart demonstrates the variety of LED indicator settings: Light Status Description Power Off No Power On Power On Off Indicates no Ethernet link detected Ethernet (Link/Activity) Green On 100 Mbps Fast Ethernet link Green Blink Data traffic on the 100 Mbps LAN Amber On 10 Mbps Ethernet link Amber Blink Data traffic on the 10 Mbps LAN Wireless Off No wireless link (Link/Activity) Green Blink Wireless Data traffic WG602 Wireless Access Point Rear Panel Power Reset & RJ-45 Ethernet Socket Restore Button Port 3 Power Socket This socket connects to the WG602 power adapter. Warning: Use only the power adapter that came with the WG602. Reset and Restore to Factory Settings Button The Reset and Restore to Factory Settings button located between the Ethernet RJ-45 connector and the Power socket reboots the WG602 or restores the WG602 to the factory default settings. Press and hold the Restore to Factory Default button for 5 seconds to clear any user-defined settings. RJ-45 Ethernet Port Use the WG602 Ethernet RJ-45 port to connect to an Ethernet LAN through a device such as a hub, switch, or router. Placement and Range Guidelines Indoors, computers can connect over 802.11 wireless networks at a maximum range of 500 feet (152.4 m) for 802.11b devices. However, the operating distance or range of your wireless connection can vary significantly, based on the physical placement of the wireless access point. For best results, identify a location for your wireless access point according to these guidelines: • Away from potential sources of interference, such as PCs, large metal surfaces, microwaves, and 2.4 GHz cordless phones. • In an elevated location such as a high shelf that is near the center of the wireless coverage area for all mobile devices. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the wireless access point. Default Factory Settings When you first receive your WG602, the default factory settings will automatically be set, as shown in the chart on the next page. You can restore these defaults with the Factory Default Settings button on the rear panel; see WG602 Wireless Access Point Rear Panel on page 3. After you install the WG602 Access Point, you may customize any of the settings to better meet your networking needs. Turn to Configuring your WG602 54 Mbps Wireless Access Point on page 7 for more information. Configuring your WG602 54 Mbps Wireless Access Point on page 7 for more information. Feature Default Factory Setttings User Name admin Password password Access Point Name netgearxxxxxx where xxxxxx are the last six digits of the AP's MAC address AP IP Address 192.168.0.227 of DHCP is disabled AP...