Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
If you select DHCP, ensure that all devices on the LAN have the TCP/IP stack set to obtain an IP address automatically (see “Setting Up the PC to Request an IP Address” on page 59). (Only in routing mode) . The modem automatically enters the start IP address for the first device on the LAN as one address higher than the Ethernet port on the modem with DHCP enabled. You cannoteditthisfield. Enter an IP address for a device that will provide Primary DNS. DNS translates human-readable machine names into IP addresses. . Enter an IP address for a device that will provide Secondary DNS. DNS translates human-readable machine names into IP addresses (optional). The modem automatically enter the Gateway IP address which is the same IP address as the Ethernet 10/100BASE-T port of the modem. You cannot edit this field. . Click Static MAC Table to get a dialog to set up static MAC addresses for the modem. The modem will learn up to 1024 MAC addresses and accept up to 32 MAC static entries. Go to “Defining or Modifying Static MAC Entries” on page 44 to configure these parameters. . Click Static Route Table to get a dialog to set up static Routing IP addresses for the modem to recognize. The modem can accept up to 32 static route entries. Go to “Defining Static Route Entries” on page 45 to configure these parameters. 5 Click Submit to accept the LAN configuration. 6 After entering a LAN IP address and subnet mask (or changing the IP address and subnet mask), effect the configuration completing the procedures for “Saving the Configuration” on page 24. Megabit Modem 400F User Manual Configuring RFC 1483 Bridging/Routing Sessions Defining or Modifying Static MAC Entries You can enter up to 32 static MAC addresses that the modem recognizes in the MAC address tables. The modem will also learn up to 1024 MAC addresses. Enter Static MAC addresses. . Enter the MAC Address for a device on the LAN. The Mac Address field is case sensitive and does not accept uppercase alpha characters; use only lowercase alpha characters (for example, 00:aa:00:46:d6:4c). Enter a number (1 through 33) for the Source Port. The port number is 1 when the source is the modem LAN port. The port number is 2 through 33 when the source is one of the 32 sessions. For example, if the source port is the second session set up (or port 2 on the EasySession page), enter the source port as 3. The source port number is always one number higher than the port number on the EasySession page. . Enter a number 1 through 33 for the Destination Port. The port number is 1 when the destination is the modem LAN port. The port number is 2 through 33 when the destination is one of the 32 sessions. For example, if the destination port is the second session set up or port 2 on the EasySession page, enter the destination port as 3. The destination port number is always one number higher than the port number on the EasySession page. . All static MAC address entries are listed in this table after you enter the parameters in fields . and . then Add them. Click Add to accept this entry. Megabit Modem 400F User Manual Chapter 6: Configuring Sessions 3 To delete a Static MAC Address Entry as follows: a Click the entry in the list shown in field . above to select it. The entry displays in the Mac address field . b Click Delete to remove the entry. 4 Click Done when you complete all configuration additions and deletions. Defining Static Route Entries You can enter up to 32 static routing IP addresses that the modem recognizes in the routing address tables, in addition to the routing IP addresses that the modem learns. (See “Routing” on page 66 for more information on defining static route entries.) 1 Enter static routes. . Enter the IP Address and net mask destination. . Enter the Gateway IP address to the next hop. 2 Click Add to accept this entry. 3 To delete a Static Route Entry: a Click the entry in the list shown in field . above to select it. The entry displays in the Static Route Entry field . and . b Click Delete to remove the entry. 4 Click Done when you complete all configuration additions and deletions. Megabit Modem 400F User Manual Activating and Deactivating Sessions ACTIVATING AND DEACTIVATING SESSIONS Use the following procedures to activate sessions as you want to use them. Additionally, you may want to deactivate some sessions while leaving other sessions active. The EasySession page provides status for each session. Up means that connection is active. Down means the connection is not active. Set-Up means the modem is negotiating the link with the service provider. Up, Down , and Set-Up are read-only fields that provide status for the session. If you power down the modem with sessions enabled, those same sessions will be enabled when you again power up the modem. Activating Sessions On the EasySession main page, select the box next to each session that you want to activate. Click to select sessions Click Enable at the bottom of the EasySession page to activate the sel...