Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Adder Technology Dateigröße: 333.86 kb Dateiname: Unterrichtssprache:

¦ Provision terminal port as follows: Data Rate — 1.2 to 19.2 kbps Asynchronous Data Format — eight data bits, no parity (none), one stop bit ¦ When using a PC with terminal software, be sure to disable any power saving programs. PROVISIONING NOTES ¦ This unit can be provisioned via the RS-232 port or remotely via ITS codes. This unit cannot be provisioned from the faceplate four-character display. Select “2” from the ADTRAN HDSL2 Main Menu Screen to view the Provisioning Screen. PRICING AND AVAILABILITY 800.827.0807 TECHNICAL SUPPORT 800.726.8663 RETURN FOR REPAIR 256.963.8722 61221001L6-30B HDSL2 TROUBLESHOOTING GUIDE PRICING AND AVAILABILITY 800.827.0807 TECHNICAL SUPPORT 800.726.8663 RETURN FOR REPAIR 256.963.8722 61221001L6-30B HDSL2 TROUBLESHOOTING GUIDE HDSL2 DEPLOYMENT GUIDELINES Cable pairs must be non-loaded Total bridged tap length < 2.5 kft No single bridged tap >2 kft 196 kHz insertion loss < 35 dB Pulse attenuation (ATTEN on HDSL2 Span Status Screen) < 30 dB Maximum loop resistance is 900 . Impulse noise < 50 dBrn as measured using a 50 kb filter Wideband noise .31 dBrn as measured using a 50 kb filter TURN UP GUIDELINES Circuit Parameters Under Normal Operation Margin .6 dB Attenuation < 30 dB Insertion Loss .35 dB No ES, SES, or UAS If these parameters are met, then the circuit will provide quality service. If not, a cable problem or excessive loss situation is probable. In this case, a more detailed cable analysis is required to insure that all HDSL2 Loop Specifications are met. These conditions may also be the result of intermittent cable faults or intermittent noise impairments. If intermittent problems are suspected, utilize the Performance History Screen (Main Menu selection #5) to assist in troubleshooting. An example of a Performance History Screen is illustrated in the bottom right- hand corner. Front Panel Indications Under Normal Operation STATUS LED will be Green (solid) NOTE: The circuit must have DSX-1 signal (from Network) and DS1 signal (from Customer) in order for the LED to be Green. If either DSX-1 or DS1 signal is not present, the LED will be Red. The four-character display will flash the current loop margin for the HDSL2 loop. No alarm or error mes- sages will be displayed. After five minutes of no activity, the display will turn completely Off. It will remain Off until MODE or SELECT is activated or a message other than loop margin is to be displayed. TROUBLESHOOTING GUIDELINES Front Panel Indicators All indicators are Off. 1. Verify that -48 Vdc is properly connected. 2. Inspect fuse and verify that it is not blown. 3. Insert the H2TU-C into a slot known to be good and verify that the STATUS indicator is lit. If card fails replace H2TU-C. ¦ Status LED is Blinking Red Poor signal quality or loss of sync. Use basic troubleshooting procedures to identify cable pair problems. ¦ Status LED is Solid Red If customer equipment is not installed, initiate an H2TU-R to Network Loopback and perform BERT test. If this test fails, or the craft interface indicates a loss of sync, then there is a problem with the cable pair that should be resolved through normal troubleshooting procedures. ¦ Status LED is Blinking Green Errors are being taken on the DSX, DS1, or HDSL2 loop. The craft interface screens will identify the source. BERT test to the appropriate loopbacks should isolate the problem. Four Character Display The error messages for this display are defined on page 1 of this guide. Craft Interface Screens Detailed Status Screen Provides instant view of system status (Main Menu selection “3”, Span Status selection “2”) Alarm History Screen Provides a record of system alarms (Main Menu selection “8”) For complete Installation and Maintenance: (877) 457-5007, Document #529, Event History Screen Provides last 100 events on the system (Main Menu selection “9”) #555, and #556. Please have your fax number available. Performance History Screens Provide performance data for all points in the system (Main Menu selection “5”) ...

Herunterladen

Geben Sie zwei Ziffern: