Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: ADTRAN Dateigröße: 185.65 kb Dateiname: 5ac1f3fd-c75b-9654-7db3-8f64d85804f1.pdf Unterrichtssprache:

However, using the AOS CLI may be necessary for more advanced configurations. ACCESS THE GUI You may access the web-based GUI from any web browser on your network by following these steps: 1. Connect the switch to your PC using the ETH 0/0 port on the back of the unit. 2. Set your PC to obtain an IP address automatically (or if using the fixed IP address, set your PC to 10.10.20.2). 3. Enter the unit’s IP address in your browser address line. The default IP address is 10.10.20.1. 4. You will then be prompted for the username and password (the default settings are admin and password). 5. The initial GUI screen appears. ACCESS THE CLI Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the NetVanta switch CONSOLE port, you need the following items: • VT100 terminal or PC (with VT100 terminal emulation software) • Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate interface for your terminal or PC communication port on the other end 1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear panel of the unit. 2. Connect the other end of the serial cable to the terminal or PC. 3. Insert the connector of the provided power cord into the power interface on the rear panel of the unit, and plug the cord into a standard electrical outlet. 4. Once the unit is powered up, open a VT100 terminal session using the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press to activate the AOS CLI. 5. Enter enable at the > prompt. 6. Enter the enable password when prompted. The default password is password. For more detailed documentation, visit us online at NetVanta 1524ST Series Switch P/N 1200560E2/L2 The configuration parameters used in the examples outlined in this document are for instructional purposes only. Please replace all underlined entries (example) with your specific parameters to configure your application. CONFIGURE THE UNIT’S IP ADDRESS The following steps create an IP address and subnet mask for the virtual interface vlan 1. If you are not sure what IP address to assign, please contact your network administrator. 1. At the # prompt, enter config terminal. 2. At the (config)# prompt, enter interface vlan 1 to access the configuration parameters for the virtual LAN (VLAN) interface. 3. Enter ip address 10.26.12.12 255.255.255.0 to assign an IP address to the VLAN interface using a 24-bit subnet mask. 4. Enter no shutdown to activate the virtual interface to pass data. 5. Enter exit to return to the Global Configuration mode. Depending on your configuration, you may need to set a default gateway as well using the (config)#ip default gateway command. ENABLE TELNET ACCESS The following steps create a password of adtran for Telnet access. By default, Telnet access is enabled with a password of password. 1. Verify that the prompt of your unit displays (config)#. 2. Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions. 3. Enter login to initiate Telnet access. 4. Enter password adtran to change the login password for the Telnet sessions. 5. Enter exit to return to the Global Configuration mode. 6. Verify that the prompt of your unit displays (config)#. 7. Enter do write memory to save the current configuration. Quick Start Guide, 61200560E1-13E, November 2006 Copyright © 2006 ADTRAN, All Rights Reserved For more detailed documentation, visit us online at ® Quick Start Guide NetVanta 1524ST Series Switch P/N 1200560E2/L2 ETHERNET PINOUTS Pin Name Description 1 TR1+ 2 TR13 TR2+ 4 TR3+ 5 TR36 TR27 TR4+ TR4 CONSOLE PINOUTS Pin Name 1 DCD Data Carrier Detect (output) 2 RD Receive Data (output) 3 TD Transmit Data (input) 4 DTR Data Terminal Ready (input) 5 SG Signal Ground 6 DSR Data Set Ready (output) 7 — Unused 8 CTS Clear to Send (output) 9 — Unused Transmit/Receive 1 Positive Transmit/Receive 1 Negative Transmit/Receive 2 Positive Transmit/Receive 3 Positive Transmit/Receive 3 Negative Transmit/Receive 2 Negative Transmit/Receive 4 Positive Transmit/Receive 4 Negative Description CONFIGURE YOUR APPLICATION More detailed documentation for configuring your ADTRAN unit is provided on the ADTRAN OS System Documentation CD included in your shipment. For more detail on hardware setup, refer to the appropriate NIM Quick Start Guides and the Hardware Installation Guide. For more detail on configuring your system, refer to the ADTRAN Operating System (AOS) Command Reference Guide, configuration guides, and technical support notes. Important: For additional details on product features, specifications, installation, and safety, refer to the appropriate Hardware Installation Guide on the ADTRAN OS System Documentation CD shipped with the base unit and available online at Quick Start Guide, 61200560E1-13E, November 2006 Copyright © 2006 ADTRAN, All Rights Reserved ...

Herunterladen

Geben Sie zwei Ziffern: