Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Menu Description 3.0 Setup Wizard This quick setup wizard can guide you through the basic settings of this Router. Please see instructions in Chapter 2.2. 3.1 Network This section allows you to configure the Internet, 3G/3.5G settings with your ISP, the settings of your local area network (LAN), such as enable/disable the DHCP server, Dynamic DNS information, and NAT function. 3.2 Wireless This section allows you to setup the Router’s SSID, security key, WPS, etc. 3.3 Application & Gaming This section allows you to configure router’s setting for your special applications or gaming requirements, such as open certain ports for your applications. 3.4 Access Restrictions This section allows you to set up the access control rules, such as MAC filtering, URL filtering to prevent the LAN users from accessing certain type of website. 3.5 Security This Firewall section allows you to configure Hacker Prevention and VPN pass through. 3.6 Administration The section allows you to specify a time zone, change the system password, save/reload the router configuration, upgrade firmware and so on. 3.7 Status You can see Router’s status in this section. 28 3.1 Network 3.1.1 WAN Use the WAN setting page to change your Internet connection type. The WAN setting page allows you to configure the Internet connection type of your ISP. The WAN settings offer the following selections for the router’s WAN port, Dynamic IP, Static IP, PPPoE, PPTP, L2TP and Telstra Big Pond. Please choose one type and complete the detail settings below. Please see Chapter 2.2, Step 5 for the detailed description of each WAN type. 3.1.2 3G/3.5G Configure the 3G/3.5G settings if you like to connect to the Broadband Internet with your 3G/3.5G USB Modem. 29 Note: The setting shown above is for Verizon 720 USB Modem. Parameter Description PIN Code Please input Pin Code for your UMTS or HSDPA or EVDO connection, this is optional, and only required if your service provider asks you to do so. APN Please input the APN code assigned by your Internet service provider here. User Name Please input user name assigned by your Internet service provider here. Password Please input password assigned by your Internet service provider here. Verify Password Please input password again for confirmation. Service Please select your service type between CDMA2000 or 3G/3.5G Only. You may try both service types if you are not sure which one your USB modem card uses. AT Dial Script Please input Dialed Number for your UMTS or HSDPA connection, the default is *99#. This field should not be altered except when required by your service provider. 3.1.3 LAN This page allows you to specify an IP address for your router, configure the DHCP Server and Static DHCP Lease Table. 30 • LAN IP section Parameters Default Description IP address 192.168.2.1 This is the router’s LAN IP address (Your LAN clients default gateway IP address). Subnet Mask 255.255.255.0 Specify a Subnet Mask for your LAN segment. 802.1d Spanning Tree Disable If you wish to activate 802.1d spanning tree function, select “Enabled”, or set it to “Disabled” If 802.1d Spanning Tree function is enabled, this router will use the spanning tree protocol to prevent from network loop happened in the LAN ports. DHCP Server Enable By enablting the DHCP server, the router will automatically give your LAN clients an IP address. If the DHCP server is not enabled then you’ll have to manually set your LAN client’s IP addresses; make sure the LAN Client is in the same subnet as this broadband router if you want the router to be your LAN client’s default gateway. .. DHCP Server section Parameters Description Lease Time Please choose a lease time (the duration that every computer can keep a specific IP address) of every IP address assigned by this router from dropdown menu. Start IP Please input the start IP address of the IP range. End IP Please input the end IP address of the IP range. Domain Name (4): If you wish, you can also optionally input the domain name for your network. This is optional. DHCP Client Range You can configure a particular IP address range for your DHCP server to assign IP addresses to your LAN Clients. Note: By default the IP range is from: Start IP 192.168.2.100 to End IP 192.168.2.200. If you want your PC to have a static/fixed IP address then you’ll have to choose an IP address outside this IP address range. Static DHCP Specify the Static DHCP Addresses for your LAN clients. Domain Name Enter the domain name of your LAN interface if there is one. 31 • Static DHCP Lease Table section This function allows you to assign a static IP address to a specific computer forever, so you don’t have to set the IP address for a computer, and still enjoy the benefit of using DHCP server. Maximum 16 static IP addresses can be assigned here. (If you set “Lease Time” to forever in DHCP Server section, you can assign an IP address to a specific computer permanently). Parameters Description Enable Static DHCP Leases Check this box to en...