Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
For detailed information on using this product, please refer to the User’s Manual on the supplied CD. Connecting the Printer Server WARNING: Only a USB printer may be connected to the USB port of the Printer Server. Connecting any other USB device to the Printer Server may damage the Printer Server. Note: Before connecting the hardware you must install the printer on each computer you plan to use with the printer. Make sure that you are able to print, scan, and fax from each with your multi-functional printer directly connected to your computer(s). Step 1 Power down the printer and the printer server. Step 2 Connect one end of a networking cable to your router, then connect the other end to the Ethernet port on the back of the print server. Step 3 Connect the USB cable coming from your printer into the USB port on the printer server. Step 4 Turn on the printer. Once the printer is powered on, connect the print server’s power adapter to an electrical outlet. Section 2 Installing the PS Software Note: The PS Software must be installed on all computers you plan to use with the print server. Step 1 Insert the Utility CD into your CD-ROM drive. When the autorun screen appears, select Install PS Software from the menu. Note: If the autorun window does not appear automatically, go to Start -> Run and type D:\Utility\Setup.exe (where D is the letter of your CD-ROM drive) and click OK. Step 2 Select your setup language and click OK. Step 3 Click Next at the welcome screen. Step 4 Click Next at the Choose Destination Location screen. Step 5 Click Next at the Select Program Folder. Step 6 Once the installation is complete, make sure that the Launch PS-Link box is checked and click Finish. Section 3 Section 3 Configuring the Printer Server Note: The following steps only need to be performed one time from one computer. Step 1 Click the Discover button and your printer should show up under Server Name. If your print server does not show up, check all power and network cable connections to the printer. You may also need to disable any software firewalls you have on your computer. Step 2 Once the printer server appears in the Server Name box, click on it. You should see your printer next to Device name. Click on the Setup Wizard button. Step 3 A password box will appear. The default password is admin. Enter it and click OK. Step 4 Click Next at the welcome screen. Step 5 At the System screen you can change the Server Name, Port Name, and Password. Click Next after making the desired changes. If you do not have a specific Server Name, Port Name, or Password that you would like to use, click Next to accept the default settings. Step 6 At the Wireless screen you can input the wireless settings for your network. If you have a router, you will want to choose Infrastructure mode. If you are unsure of your SSID, contact your router manufacturer for assistance. Step 7 At the Wireless Encryption screen you can enter the wireless security settings of your router. If you do not use encryption, click Disable and then Next. If you are using encryption, you can get the encryption settings from your router or router manufacturer and enter them here. Afterwards, click Next. For WEP encryption, select WEP and enter your settings into the boxes below. For WPA-PSK, Select WPA-PSK and enter your Pre-Shared Key into the box. Please note that the print server only supports TKIP and does not support AES. Step 8 If you have a specific IP address you would like to assign to the print server, select Manually Assign and enter your custom settings. Otherwise, select DHCP Assign Automatically and click Next. Step 9 If your network uses a workgroup name other than WORKGROUP, you can enter it here, or accept the default settings, and click Next. Step 10 If you have specific AppleTalk settings, you can enter them here or accept the default settings, and click Next. Step 11 Click Save to save the changes to your print server. If you plan to use the print server wirelessly, you can now disconnect the Ethernet cable between the print server and the router. Section 4 Section 4 Configuring the Computer Note: The following steps must be completed on all computers you plan to use with the print server. Step 1 Double click on the PS-Link icon in the system tray to open the PS-Link software. Step 2 Click the Discover button and your printer should show up under Server Name. If your print server does not show up, check all power and network cable connections to the printer. You may also need to disable any software firewalls you have on your computer. If you are using the print server wirelessly, please refer to Section 5 for wireless troubleshooting steps. Step 3 Select your print server from the Server Name box and click the Link button. Step 4 Click OK at the Link Successfully screen. You will see notices appearing in the bottom right-hand corner of your screen while Windows configures the printer. Step 5 Once you see a notice that says Your new hardware is ins...