Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
For moredetailed information, please refer to the user’s manual on the supplied CD. Connecting the Router Note: Prior to connecting the router, be sure to power off your computer, DSL/Cable modem, and therouter. You should setup the router with a wired connection first before attempting to setup any wirelessconnection. Step 1 Connect one end of a network cable to the WAN port of the router and connect the other end of the cable to the DSL/Cable modem. Step 2 With another network cable, connect one end of the cable to your computer’s network card and connect the other end to one of the LAN ports of the router. Step 3 Power on the DSL/Cable modem and wait for the lights on the modem to settle down. Step 4 Power on the router by connecting one end of the supplied power adapter to the power jack of therouter and connecting the other end to an electrical outlet. Step 5 Power on your computer. Step 6 Make sure the WAN, WLAN, and the LAN port that the computer is connected to are lit. If not, trythe above steps again. Section 2 Section 2 Verify Connection to Router Step 1 Go to Start, Run, type command (for Windows 95/98/ME) or cmd (for Windows 2000/XP) andclick OK. You will see the command prompt as below. Step 2 Type ping 192.168.1.1 and press Enter. You should get four reply responses back. Step 3 If you get Request timed out, or Destination host unreachable, double-check the network cable connection between the computer and the router and try Step 2 again. If you still encounterproblem, go to the next step; otherwise proceed to Section 3, Configuring the Router. For Windows 2000/XP Step 4 At the command prompt, type ipconfig/release and press Enter. Step 5 After the IP address is released, type ipconfig/renew and press Enter. You should get an IP address of 192.168.1.x (where x is a number between 2 - 254). Proceed to Section 3, Configuring theRouter. If you don’t get an IP address, reset the router by holding in the reset button at the back of therouter for 10 seconds while it is ON and try ipconfig/renew again. For Windows 95/98/ME Step 4 Go to Start, Run, type winipcfg and click OK. Step 5 Select your network card from the drop-down menu and click Release. Step 6 After the IP address is released, click Renew. You should get an IP address of 192.168.1.x (where x is a number between 2 - 254). If you don’t get an IP address, reset the router by holding in thereset button at the back of the router for 10 seconds while it is ON and try Renew again. Section 3 Configuring the Router Step 1 Open the web browser and type 192.168.1.1 in the URLAddress field. Step 2 Enter admin for both the User name and Password fields and click OK. Step 3 Click Setup Wizard at the router’s main screen. Step 4 Click Next at the Setup Wizard. Step 5 Select your type of Internet Access. If you are not sure what type of connection you have, pleasecontact your Internet Service Provider (ISP) for assistance. For Cable Modem Users: Step 6a Click on Clone MAC Address, click OK, then click Next. Proceed to Step 7. For DSL Users: Step 6b For most DSL users, select PPPoE and click Next. Otherwise, choose your Login procedurefor connecting to the Internet. Step 6c For PPPoE users, enter your Username and Password required to get online and click Next. Note: some ISP’s require the domain name to be included with your username. Example: username@sbcglobal.net Step 7 Choose your IPAddress assignment and click Next. For most users, you can use the defaultsettings (Dynamic IP Address). If you are using a Static IP assigned by your ISP, select Specified IP Address and enter the applicable values. Step 8 Make sure the Test Internet Connection box is checked and click Finish then OK to begin theInternet Connection Test. Step 9 Verify that the Internet Connection Test is successful and click Close. If the test did not pass, please refer to Section 5 Troubleshooting. Section 4 Section 4 Connecting to the Router Wirelessly Below are the default wireless settings of the router. You must configure your wireless network card to thesame settings in order to establish a wireless connection with the router. Please refer to your wirelessnetwork card’s manual for configuring these settings. SSID: default Operating Mode: Infrastructure Channel #: 11 WEP: disabled You may need to restart your computer after establishing a signal strength/link quality with the router. Section 5 Troubleshooting If the Internet Connection Test fails, try the following steps: Step 1 Power off the Cable/DSL modem, router, and computer and wait for 5 minutes. Step 2 Turn on the Cable/DSL modem and wait for the lights on the modem to settle down. Step 3 Turn on the router and wait for the lights on the router to settle down. Step 4 Turn on the computer. Step 5 Redo the Setup Wizard. Step 6 Verify the Internet Connection Test is successful. If you can ping the router but cannot access the router’s web configuration page, try the following steps: For Windows 9x/ME/2000 Step 1 Go to Start, S...