Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Altinex Dateigröße: 3.08 mb Dateiname: 308f9a9e-a7d0-4c09-a3d5-e23d4b77788c.pdf Unterrichtssprache:

MT107-301/305/306 Mechanical ELECTRICAL MT107-301/305/306 Video Output Signals R,G,B Impedance Analog 75 Ohms Analog Signal Level 1.5V p-p max. Sync Output Signals H,V Signal Level 3 - 5 Volts TTL Bandwidth Bandwidth 450 MHz @ -3dB Table 3. MT107-301/305/306 Electrical 3 PRODUCT DESCRIPTION 4 PRODUCT DESCRIPTION 4 MULTI-TASKER™ 4 MULTI-TASKER™ APPLICATION DIAGRAM 5 DIAGRAM 1: TYPICAL CONFIGURATION 5 MULTI-TASKER™ DIAGRAM 2 INTERNAL VIEW MT107-301 MT107-301, 8 BNC OUTPUTS 450MHz, VIDEO/SYNC INPUTS OUTPUTS 40 PIN IDC FROM TO FRONT PANEL BNCs MT107-100 MATRIX ENGINE IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 VIDEO SYNC VIDEO VIDEO VIDEO SYNC VIDEO SYNC SYNC SIGNAL DETECT SYNC SYNC VIDEO VIDEO SYNC SYNC VIDEO OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8 6 MULTI-TASKER™ DIAGRAM 3 INTERNAL VIEW MT107-305 MT107-305, 8 BNC OUTPUTS 450MHz, VIDEO INPUTS OUTPUTS 40 PIN IDC FROM TO FRONT PANEL BNCs MT107-100 MATRIX ENGINE IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 SIGNAL DETECT VIDEO VIDEO VIDEO VIDEO VIDEO VIDEO VIDEO VIDEO OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8 7 MULTI-TASKER™ DIAGRAM 4 INTERNAL VIEW MT107-306 MT107-306, 8 BNC OUTPUTS, SYNC INPUTS 40 PIN IDC FROM MT107-100 MATRIX ENGINE TO FRONT PANEL BNCs OUTPUTS IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 SIGNAL DETECT SYNC SYNC SYNC SYNC SYNC SYNC SYNC SYNC OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8 8 MULTI-TASKER™ INSTALLING YOUR MT107-301/305/306 6 OPERATION 7 Step 1. Locate the MT107-100 currently installed in the Multi-Tasker™. Ensure there are enough empty slots in the enclosure to allow for the one or more MT107-301/305/306's to be installed. Step 2. Route the ribbon cables through the notch in the add-on boards and connect to the MT107-100 base assembly using special high bandwidth cables provided with the Engine. Make sure that cable connector is secured in the socket of the input card. Step 3. Carefully, slide the MT107-301/305/306 into slot of the Multi-Tasker™ Enclosure. Step 4. Secure each card by tightening the retainer screws at the top and bottom of each card. 7.1 RS-232 CONTROL The MT107-301/305/306 has many advanced remote control capabilities when used in the Multi-Tasker™ Enclosure as part of an MT107-100 Matrix Switcher. These capabilities are accessible through standard RS-232 communication. The actual controlling can be accomplished through a computer control system or any other device capable of sending RS-232 commands. 7.2 DESCRIPTION OF COMMANDS Please, see the MT107-100 User's Guide for a full listing of commands available for the MT107 301/305/306 as part of a Multi-Tasker™ Matrix Switcher. TROUBLESHOOTING GUIDE 8 We have carefully tested and have found no problems in the supplied MT107-301/305/306. However, we would like to offer suggestions for the following: 8.1 BAD SIGNAL Cause 1: The display is connected to the wrong card. Solution: Make sure the video signals are coming from the video card (-305) and sync signals are coming from the sync card (-306). If the signal is still bad, see Cause 2. Cause 2: The switch settings are wrong. Solution: If the output card is an MT107-301, make sure the Video/Sync switch settings are in the correct position for the signal type on each channel. If the signal is still bad, call Altinex at (714) 990-2300. 9 MULTI-TASKER™ 8.2 NO DISPLAY Cause 1: The source has a problem. Solution: Check the source and make sure that there is a signal present and all source connections are correct. If the ...

Herunterladen

Geben Sie zwei Ziffern: