Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. Sewage Pump Description A sewage system consists of a pump, control switch, and a basin for use in applications where less than six toilets (units) are discharged into the basin. The system is generally controlled by a float switch with a plug-in-plug which accepts the pump plug and in turn plugs into a 115 volt outlet. The float switch is a wide angle differential switch that rises with the liquid level and turns the pump on. As the liquid level decreases the float lowers and turns the pump off. This pump is intended for use in domestic sewage lift stations. It is suitable for pumping sewage, effluent, wastewater, groundwater and other nonexplosive, noncorrosive liquids with up to 2 inch solids. Specifications unpacking Inspect this unit before it is used. Occasionally, products are damaged during shipment. If the pump or components are damaged, return the unit to the place of purchase for replacement. Failure to do so could result in serious injury or death. Safety Guidelines This manual contains information that is very important to know and understand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe the following symbols. Danger indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Construction Warning indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Caution indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. Notice indicates important information, that if not followed, may cause damage to equipment. General Safety Information CALIfORNIA PROPOSItION 65 This product or its power cord contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. Power supply requirements .............. 115V, 60 hz Motor body material............Cold rolled steel Circuit requirements.......................... 15 amps (min) Motor housing......................Glass reinforced Motor duty......................................... Intermittent polypropylene Motor ................................................. 115V, 1 Phase, 1725 RPM Volute....................................Glass reinforced ABS Horsepower .......................................4/10 (SEL40); 1/2 (SEL50) Impeller.................................Glass reinforced PBT Motor full load .................................. 12 amps Seal plate ..............................Cast Iron Liquid temperature range................. 40. F to 120. F Shaft seal...............................End faced mechanical Max. operating position.................... 45. from vertical Dimensions......................................... 13-1/2 inch x 11 inch Intake ................................................. 2 inch Performance Discharge............................................ 2 inch NPT female, 3 inch NPT male Cut-in level (factory set)....................18 inch Cut-out level (factory set) ................. 10 inch GALLONS PER hOuR At tOtAL hEAD IN fEEt Model 10 15 200 SEL40 3700 1350 Differential......................................... 8 inch SEL50 6420 4200 1500 Switch.................................................90. wide angle mechanical tether switch Power cord.........................................16 gauge 3 conductor w/plug REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping. © 2009 Wayne Water Systems For parts, product & service information 330002-001 3/09 visit Operating Instructions and Parts Manual General Safety Information 6. Check hoses for weak and worn condition before each use, making (Continued) certain that all connections are GENERAL SAfEty secure. 1. Know the pump application, 7. Periodically inspect the pump and limitations, and potential hazards. system components. Perform routine Do not use to pump flammable or explosive fluids such as gasoline, fuel oil, kerosene, etc. Do not use in a flammable and/or explosive atmosphere. Personal injury and/or property damage could result. 2. Make certain that the power source (electric motor) conforms to the requirements of the equipment. Disconnect power before servicing. If the power disconnect is out of sight, lock in the open position and tag it to prevent unexpected application of power. Failure to do so could result in fatal electrical shock! 3. Release all pressure within the system before servicing any component. 4. Drain all liquids from the system before servicing. 5. Secure the discharge line before starting the pump. An unsecured maintenance as required (See Maintenance Section). 8. Provide a means of pressure relie...
Dieses Handbuch ist für folgende Modelle:Plumbing - SEL40 (654.51 kb)
Plumbing - SEL50 (654.51 kb)