Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Haier Dateigröße: 1.8 mb Dateiname: Unterrichtssprache:

Wetted materials on all models . . . . . . . . . . . . . . . . . . . . 316 SST, 3A Approved EPDM, PTFE, Wetted material depending on model. . . . . . . . . . . . . . . . Santoprene®, 3A Approved EPDM, PTFE CAUTION: Santoprene® may be used only with non-fatty, non-oily foods or alcohols up to 15%. 300 series stainless steel, polyester (labels), LDPE foam Non-wetted external parts . . . . . . . . . . . . . . . . . . . . . . . . (gasket) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 lb (44 kg) Santoprene® is a registered trademark of the Monsanto Co. Loctite® is a registered trademark of the Loctite Corporation. * Displacement per cycle may vary based on suction condition, discharge head, air pressure, and fluid type. ** Noise levels measured with the pump mounted on the stand. Sound power measured per ISO Standard 9614-1. *** The pump user must verify that the construction materials meet their specific application requirements. 34 310622L Model 1590 Model 1590 Performance Chart Test Conditions: Pump tested in water with inlet submerged To find Fluid Outlet Pressure To find Pump Air Pressure (psi/MPa/bar) at a specific fluid flow (gpm/lpm) and (scfm or m3/min) at a specific fluid flow (gpm/lpm) and operating air pressure (psi/MPa/bar): operating air pressure (psi/MPa/bar): 1. Locate fluid flow rate along bottom of chart. 1. Locate fluid flow rate along bottom of chart. 2. Follow vertical line up to intersection with selected 2. Read vertical line up to intersection with selected air fluid outlet pressure curve. consumption curve. 3. Follow left to scale to read fluid outlet pressure. 3. Follow left to scale to read fluid outlet pressure. 1590 3A Performance Chart 120 120 (8.4, 0.84) (3.4) 100 100 Fluid Outlet Pressurepsi (bar, MPa) (7, 0.7) 80 (5.5, 0.55) 60 (4.2, 0.42) 40 (2.8, 0.28) 20 (1.4, 0.14) (2.8) 80 (2.2) 60 (1.7) 40 (1.1) 20 (0.6) Air Consumptionscfm ( m3/min) 0 20 40 60 80 100 120 0 (76) (152) (227) (303) (379) (454) TI8646 Fluid Flow gpm (lpm) TI8647 310622L 35 Model 3150 Model 3150 Dimensional Drawing 3A Ball Check Valve Pumps 6.5 in. (165.1 mm) 22.0 in TI4929d (558.8 mm) 23.5 in. (596.9 mm) 28.4 in. (721.4 mm) 37.6 in. (955.0 mm) TI7610c Flapper Check Valve Pumps Sanitary Ball Check Valve Pumps TI4685d 37.5 in. (952.5 mm) 19.3 in. (490.2 mm) 28.3 in. (718.8 mm) 6.5 in. (165.1 mm) TI4928d 19.3 in. (490.2 mm) 29.5 in. (749.3 mm) 5.9 in. (149.9 mm) 38.1 in. (967.7 mm) 36 310622L Model 3150 Model 3150 Technical Data Maximum fluid working pressure . . . . . . . . . . . . . . . . . . . 120 psi (0.8MPa, 8 bar) Air pressure operating range . . . . . . . . . . . . . . . . . . . . . . 20-120 psi (0.14-0.8 MPa, 1.4-8 bar) Maximum air consumption . . . . . . . . . . . . . . . . . . . . . . . . 175 scfm Air consumption at 70 psi air inlet pressure/60 gpm. . . . . 50 scfm (see chart) Maximum free-flow delivery . . . . . . . . . . . . . . . . . . . . . . . 150 gpm ( 570 l/min) Maximum pump speed. . . . . . . . . . . . . . . . . . . . . . . . . . . 145 cpm * Gallons (Liters) per cycle . . . . . . . . . . . . . . . . . . . . . . . . 1.03 (3.90) Maximum suction lift.. . . . . . . . . . . . . . . . . . . . . . . . . . . . Flapper 10ft (3.5 m) wet, 5 ft (1.75 m) dry Ball 18 ft (5.5 m) wet, 9 ft (2.75 m) dry Flapper 2.5 in. (63.5 mm) Maximum size pumpable solids . . . . . . . . . . . . . . . . . . . . Ball 1.0 in. (25.4 mm) ** Maximum Noise Level at 100 psi, full flow . . . . . . . . . . 90dBa ** SoundPower Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 dBa ** Noise Level at 70 psi and 50cpm. . . . . . . . . . . . . . . . . 85 dBa Maximum fluid operating temperature is based on the PTFE 220°F (104.4°C) following maximum diaphragm, ball, and seat temperature Santoprene® 180°F (82.2°C) ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Buna-N 180°F(82.2°C) fluoroelastomer 250°F (121.1°C) 3A Approved EPDM 275°F (135°C) Air inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 in. npt(f) Wetted parts ***All fluid contact materials are FDA-compliant and meet the United States Code of Federal Regulations (CFR) Title 21, Section 177. 316 SST, 3A Approved EPDM Wetted materials on all models. . . . . . . . . . . . . . . . . . . . . 316 SST, Santoprene®, Buna-N (Nitrile), fluoroelastomer, Wetted material depending on model . . . . . . . . . . . . . . . . 3A Approved EPDM, PTFE CAUTION: Santoprene® may be used only with non-fatty, non-oily foods or alcohols up to 15%. 300 series stainless steel, polyester (labels), LDPE foam Non-wetted external parts. . . . . . . . . . . . . . . . . . . . . . . . . (gasket) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 lb (66 kg) Santoprene® is a registered trademark of the Monsanto Co. Loctite® is a registered trademark of the Loctite Corporation. * Displacement per cycle may vary based on suction condition, discharge head, ai...

Herunterladen

Geben Sie zwei Ziffern: