Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
Bradley cannot assume any responsibility for any improperly installed units. Read this entire installation manual to ensure proper installation. When fi nished with the installation, file this manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances is the responsibility of the installer. Separate parts from packaging and make sure all parts are accounted for before discarding packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. Make sure that all water supply lines have been flushed and then completely turned off before beginning installation. Debris in supply lines can cause valves to malfunction. Product warranties may be found under “Products” on our web site at bradleycorp.com. Installation THISSIDEUP Packing List • • • • Stainless Steel Combination Unit Table of Contents Supplies Required ........................... 2 Rough-In Information ...................... 2, 3 Installation Instructions ....................... 3 Cleaning Instructions ......................... 4 215-329 Rev. K EN 08-703 P.O. Box 309, Menomonee Falls, WI 53052-0309 © 2008 Bradley Corporation Phone: 1-800-BRADLEY Fax: 262-253-4161 Page 1 of 4 9/30/08 COMBI5500 Installation Supplies Required: • 1" NPT supply piping to flush valve • Toilet/Lav waste connections • For optional air valve manifold: 1/2" NPT supply piping. Refer to Bradley Installation Manual (215-1158) provided with assembly. • For optional self-closing valve: 1/2" NPT supply piping. Refer to Bradley Installation Manual (215-581) provided with assembly. • For optional TouchTime® solenoid valve: 1/8" NPT supply piping; wire nuts sized for 22 AWG to connect to 24 VAC power source. Refer to Bradley Installation Manual (215-1378) provided with assembly. Roughing-In Supplies, Drain, and Waste Outlet 7-1/2" (190) 4" (102) Square Hole 8" (203) Square Hole 3" x 5" (76 x 127) Hole Threaded Studs (6) Lav Waste Flush Valve Supply Toilet Waste 34-1/2" (876) 23-3/4" (603) 15" (381) Top of Integral Seat 11-1/4" (286) 14" (356) 7" (178) 7-3/4" (197) 4-1/2" (190)4" (102) 31-1/2" (800) Finished FloorFinished Floor 20" (508) 22" (538) 31" (787) 7/8" (22) Dia. Holes [5] 15" (381) 15" (381) 2" X 15" (51 x 381) Valve Mounting Hole (mm) Single Opening in Wall* Multiple Openings in Wall Top of integral seat is to be mounted 15" ( 381 mm) above finished floor. On floor outlet waste units, centerline of waste is 4-1/4" (108mm) from wall. All views are from the fixture side (right-hand unit shown). Rough-in 1-1/4" or 1-1/2" NPT (size dependent on options ordered) lavatory waste outlet at the dimensions shown below. Use single or multiple openings, depending on site requirements. *Recommended when using optional wall sleeve 9/30/08 Bradley Corporation • 215-329 Rev. K; EN 08-703 Installation COMBI5500 Bradley Corporation • 215-329 Rev. K; EN 08-703 9/30/08 3 Five-Sided Unit Dimensions 17" (432) 4-1/4" (108) 18" (457) 14" (356) Top View 23-1/2" (597) 17" (432) 19-11/16" (500) 16-1/2" (418) 14" (356) 18" (457) 23-3/8" (721) 12-1/4" (311) 4-1/4" (108) Floor Waste Option COMBI55000 Series (Center Confi guration) COMBI55000 Series (Angle Confi guration) All fasteners must be securely tightened to approximately 30 ft./lbs. When fi nished, turn on the water supplies and check for leaks and adequate water fl ow. Activate lavatory pushbuttons and fl ush valve several times to purge air from the lines. AInsert six 1/2"-13 threaded studs (supplied by installer) into the back of the unit and screw in approximately 1/2". B Connect the flush valve supply pipe, lav waste, and toilet waste (supplied by installer) to the couplings located on the back of the fixture. CSliding studs and pipes through the wall openings, position the fixture in place (top of integral toilet seat is 15" above finished floor). Mount Valve Asembly. DSecure the fixture to the wall using anchor brackets, washers, and nuts provided. Valve Mounting Plate (159-292) Mounting Channel (140-558) Washer (140-002AM) Nut (110-119) 1/2" -13 Threaded Stud 0" - 4" Wall (109-039) 4" - 8" Wall (109-040) 8" - 12" Wall (109-048) 1 Install Unit Side View 32-1/2" (826) 15" (381) 3-1/8" (79) Wall-Mounted Units Only 3-1/2" (89) 3-1/2" (89) 32-1/2" (826) 15" (381) 3-1/8" (79) Wall-Mounted Units Only Floor Waste Option 12-1/4" (311) COMBI5500 Installation Cleaning Stainless Steel Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive. Proper care, particularly under corrosive conditions, is essential. Always start with the simplest solution and work your way toward the more complicated. Routine Cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia. Apply the cleaning solution per the manufactures instructions and always use a soft cloth or sponge to avoid damaging the finish. Stubborn Stains: To remove stains from stainless steel use a stainless steel...