Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Axor Dateigröße: 747.63 kb Dateiname: Install_1644.pdf Unterrichtssprache:

Install SEAL (4) into coupling nut of TEE (5) and tighten connection to ADAPTER (2). Connect HOSE COUPLING NUTS (6) to Hot and Cold valve bodies and securely tighten. 7 6 7a 6 Front 9 Push DIVERTER KNOB (1) onto HANDLE ADAPTER (2). Push on RING (3) and tighten with SCREW (4). Press on KNOB CAP (5). Note: Screwdriver gap is for disassembling and should point downwards. 4 2 COMPRESSION NUT COUPLING NUT OUTLINE OF BIDET 3/8 O.D. BULL-NOSE RISERS CONNECT TO WASTE OUTLET 2 3 4 5 FERRULE 3 M968845 Rev. 1.2 INSTALL HANDLES CHECK DRAIN CONNECTIONS 12 11 13 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Operate both HANDLES (1) to flush water lines thoroughly. Rotate TRANSFER VALVE (5) from rim wash to spray several times to check operation. Pull up POP-UP KNOB (3) and fill Bidet with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Bidet. If STOPPER (4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions. Push POP-UP KNOB (3) down and check all drain connections and "P" trap for leaks. Tighten if necessary. 1 1 4 SPRAY OUTLINE OF BIDET 2 2 4 1 2 4 5 3 TOP Figure "A" SPLINE END DOWN Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) without a spline is facing up. See figure "A". Tighten STEM SCREW (3) to secure ADAPTER (1). Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4). Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5) until snug against mounting surface. THREAD ON TO DECK ADAPTER 14 15 SERVICE 2 90° To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Unthread HANDLE BASE (1) from DECK ADAPTER (2). Pull HANDLE ASSEMBLY off VALVE STEM (3). Remove SPRING CLIP (4). Lift STOP WASHER (5), turn 90° and replace. Replace SPRING CLIP (4). Find correct position of HANDLE ASSEMBLY by adjusting male teeth on VALVE STEM (3) to female teeth in HANDLE. Thread HANDLE ASSEMBLY onto DECK ADAPTER (2) until snug against mounting surface. If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90° . 1 4 3 5 UNTHREAD HANDLE ASSEMBLY 3 DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER.DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. CARE INSTRUCTIONS: M968845 Rev. 1.2 SpeedConnect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B. Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D. Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E. The Stopper can now be removed by lifting it out of the Drain. Fig. F. CAM CAM CAP CABLE ADJUSTMENT PROCEDURE If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT...

Herunterladen

Geben Sie zwei Ziffern: