Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Delta Dateigröße: 975.97 kb Dateiname: Install_4242.pdf Unterrichtssprache:

Threads of VALVE BODY (8) should extent at least 5/16 of a inch above mounting surface top. Fig. B. Thread ADAPTER (10) onto VALVE BODY (8) until snug against internal stop. If necessary, adjust LOCKNUT (11). 8 11 Place RUBBER RING (9) into ADAPTER (10). 5/16'' MIN. 8A Fig. B. 7420.801 7420.821 Series 7415.801 7415.821 Series Installation Instructions PORTSMOUTH™ Spread Lavatory Faucet with Speed Connect™ Drain 10 9 10 9 Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found onlyon American Standard faucets. *Your new American Standard faucet is designed to work only with the Speed Connect drain. Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. 7420 Speed Connect Drain* 7415 • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. 2 6 POP-UP KNOB (1) must be fully down. Fig. B. FLANGE GASKET AND POP-UP KNOB Fig. A. Fig. B. Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET (3) is fully compressed and not visible. Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 4 3 TIGHTEN LOCKNUT 1 REMOVE FLANGE Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 2 2 3 3 1 1 Tighten LOCKNUT (1) firmly with Adjustable Wrench or Channel Locks. INSTALL DRAIN FROM BELOW FIXTURE 5 From under side of SINK install DRAIN BODY (1) up through drain outlet. Note: No plumber’s putty or caulk is required. The CABLE ATTACHMENT POINT (2) must face towards the rear of the SINK. Install FOAM GASKET (3) and FLANGE (4) onto drain body from above SINK and tighten FLANGE (4) firmly. 4 Fig. A. Fig. B. Fig. A. Fig. B. 2 DRAIN OUTLET 1 3 4 REAR OF SINK DRAIN BODY 4 WHITE FOAM GASKET NOT VISIBLE DRAIN FLANGE 1 DOWN M965015 REV.1.7 Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. Thread TEE BODY (4) to SPOUT SHANK (5). Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A). 9 Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY. HOT COLD FERRULE COMPRESSION NUT COUPLING NUT FLEXIBLE SUPPLIES 1 1A 3/8 O.D. BULL...

Herunterladen

Geben Sie zwei Ziffern: