Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Delta Dateigröße: 249.43 kb Dateiname: Install_5333.pdf Unterrichtssprache:

Do not use putty. 4 5 8 6 Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. 7 4 5 8 6 7 9 10 3 2 On model with separate spray, place the SPRAY HOLDER (1) into the appropriate mounting hole. Assemble the SPRAY HOLDER WING NUT (2) onto the shank of SPRAY HOLDER (1) from below and hand tighten. Do not use putty. For installation less spray, cap off SPRAY HOSE CONNECTION (3) with PIPE CAP (4). 3 INSTALL SPRAY HOLDER 1 1 2 5 4 2 TEST INSTALLED FAUCET Move HANDLE down into "off" position and remove AERATOR (1). Turn on water supplies and check connections for leaks. Operate HANDLE (2) up and down, left and right to flush water lines thoroughly. For faucet with spray, direct SPRAY HEAD (3) into sink and activate SPRAY (3). Check hose connections for leaks. Move HANDLE (2) down to "off" position and replace AERATOR (1). CHECK CONNECTIONS FOR LEAKS 6 3 4 CONNECT HOSE SPRAY Feed SPRAY HOSE (5) through SPRAY HOLDER (1) and attach COUPLING NUT (6) of HOSE (5) to SPRAY HOSE CONNECTION (3) on valve body. Tighten COUPLING NUT (6) firmly. 2 SPRAY HOSE CONNECTION MAKE WATER SUPPLY CONNECTIONS Turn off hot and cold water supplies before beginning. Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply to Hot (Marked with a Red Line) and right supply to Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten. Faucet supplies are 21" long from faucet base. Note: If additional supply length is required, installer must purchase additional parts separately. Important: If SUPPLY HOSES (1, 2) are too long, loop as illustrated to avoid kinking. M965115_Rev.1.2 1 2 COLD HOT 3 M965115_Rev.1. 2 Spout leakage. If fitting leaks above or below SPOUT HUB remove SPOUT as follows and check SPOUT O-RINGS. First turn off water supply. Remove HANDLE BUTTON (2) and loosen SET SCREW (1) with 2.5mm HEX WRENCH (11) supplied. Pull HANDLE (3) off valve stem. Pull off CAP (4). Loosen CARTRIDGE SCREWS (5) and remove CARTRIDGE (6). Remove SPOUT (7) by pulling up gently while moving SPOUT (7) side to side. Check both SPOUT O-RINGS (8) for damage. Replace if necessary. On models with SPRAYS, DIVERTER (9) can be cleaned by pulling DIVERTER (9) out of the MANIFOLD (10). Rinse clean the DIVERTER (9) and MANIFOLD (10). Push DIVERTER (9) back into MANIFOLD (10). Reverse procedure to reinstall SPOUT, CARTRIDGE and HANDLE. Remove PLUG BUTTON (2), loosen HANDLE SCREW (1) and remove HANDLE (3). Remove ESCUTCHEON CAP (4). Unscrew the three CARTRIDGE SCREWS (5). Clean MANIFOLD (10), CARTRIDGE (6) ports and SEALS (13). Clean inlets of CARTRIDGE (6) and MANIFOLD (10). Reassemble CARTRIDGE (6), alternately tightening SCREWS (5). Replace CAP (4) and HANDLE (3). Check flow. SERVICE 5Clogged CARTRIDGE outlets or inlets may cause reduced flow. To clean, ...

Herunterladen

Geben Sie zwei Ziffern: