Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Delta Dateigröße: 168.59 kb Dateiname: Install_2059.pdf Unterrichtssprache:

1.5 Required Tools Phillips Screwdriver Flat Blade Screwdriver Adjustable Wrench Channel Locks ^CD3 Plumbers' Putty or Caulking ROUGHING-IN DIMENSIONS BOTTOM OF / TUB INSTALL TRIM CAUTION: Protect finish on SHOWER ARM, SHOWER HEAD and TUB SPOUT when installing. When finished tiling the wall, remove PLASTER GUARD (A) and turn off water supply. Push CAP (1) over VALVE CARTRIDGE (2). Mount ESCUTCHEON (3) to valve body with SCREWS (4). Remove PIPE CAPS (5) from shower pipe and tub filler pipe. Install SHOWER ARM (G), SHOWER HEAD (7) by threading onto pipe nipples using teflon tape or pipe sealant. Install SLIP-ON TUB SPOUT (8). Tighten with HEX WRENCH supplied. 8 HEX WRENCH INSTALL HANDLE Install HANDLE BUSHING (1) onto CAP (2). Find connect position of HANDLE (3) and push HANDLE (3) onto VALVE STEM (4). Install HANDLE SCREW (5) and push in INDEX CAP (6). Check pnopen operation of HANDLE. Turn waten supply on and test installed fitting. Operate valve and diventen spout. 6 3 ADJUST HOT LIMIT STOP ■ By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP (1) reduces risk of accidental scalding. To set the maximum hot water temperature of your faucet, you need to adjust the setting on the HOT LIMIT SAFETY STOP (1). ■ Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustment to HOT LIMIT STOP (1). Use a flat blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1). Pull forward and rotate counterclockwise one number to limit hot water temperature. Use ARROW (3) on CARTRIDGE (4) and NUMBERS (5) on HOT LIMIT STOP (1) for indication. 1 2 3 4 TO GAIN ACCESS TO VALVE FOR SERVICING ■ Pull INDEX CAP unscrew HANDLE SCREW and pull HANDLE off valve stem. ■ Remove two SCREWS holding ESCUTCHEON and remove ESCUTCHEON. ■ Remove COVER by pulling straight out. ■ Shut off water supply by either closing off main water supply, or closing off the hot and cold CHECK STOPS on valve. VALVE LEAKS WHEN SHUT OFF ■ Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2). Remove three SCREWS (3) from FIXATION RING (4) and pull out PRESSURE BALANCING (5) unit. ■ Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE BALANCING UNIT (5) and clean O-RINGS (6). Remove CAPS (7) and check O-RINGS on inside of CAPS (7) for debris. Clean inside sealing surfaces of VALVE BODY (8). Re-assemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1). Tighten all screws. ■ Turn on water supply and see above for installing TRIM and HANDLE. If it still leaks, replace pressure balancing unit (M952100-0070A). UNABLE TO MAINTAIN CONSTANT TEMPERATURE ■ Remove PRESSURE BALANCE UNIT (5). ■ Remove CAPS (7) and clean valve thoroughly. ■ Examine balancing unit and check condition of O-ring on end of piston. Piston should move back and forth. Order Repair Part M952100-0070A if balancing unit is defective. ■ Replace CAPS (7) and install PRESSURE BALANCE UNIT (5...

Herunterladen

Geben Sie zwei Ziffern: