Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
O.D. washers to mount main frame and bowl to wall (minimum pull-out rating of 1,000 lbs.) • (2) #10 wall anchors (for optional mixing valve/bracket mounting) • 1/2" NPT hot/cold or tempered supply piping • 1-1/2" NPT drain piping • OPTIONAL: 110 volt GFCI protected electrical outlet for 100–120 VAC plug-in transformer (for Bradley Faucets) • OPTIONAL: 240/208 or 277 volts for electric tankless water heater Installation FL-1H, FL-1L Cleaning and Maintenance for Terreon® Material Description: Terreon® is an NAHB Certified densified solid surface material composed of polyester resin and is resistant to chemicals, stains, burns and impact. Surface damage can be easily repaired with everyday cleansers or fine grit abrasives. Routine Cleaning: Clean daily or as often as conditions require using a standard commercial or household cleaner such as Formula 409® or Windex®. Stubborn Stains: Remove tough stains with Ajax®, Comet®, or Soft-Scrub® and a green Scotch-Brite® pad or lightly sand in a circular motion with 240 grit wet/dry sandpaper. The finish can be renewed with a maroon Scotch-Brite® pad. Special Situations for Material Scratches: Remove scratches with a green Scotch-Brite® pad. The finish can then be renewed with a maroon Scotch-Brite® pad, followed by a white Scotch-Brite® pad or 30-micron sandpaper. Hard Water Deposits: Remove hard water deposits with a mild solution of vinegar and water. Always rinse the unit thoroughly after cleaning. Restoring the surface: Use Hope’s® Solid Surface cleaner and polish to refresh and protect the Terreon® Solid Surface material. Bradley recommends additional care and maintenance for the darker colored Terreon®, for complete instructions on this additional maintenance refer to Bradley technical document #1505. Do not use strong acid or alkaline chemicals and cleansers to clean Terreon®. If these chemicals come in contact with the surface, wipe them off immediately and rinse with soapy water. Avoid contact with harsh chemicals such as paint remover, bleach, acetone, etc. Avoid contact with hot pans and objects. Repair Kits: Terreon® repair kits are available. Contact your Bradley representative or distributor for part numbers and pricing Repair kits are made to order and have a shelf life of 30 days. Terreon® is a unique, cast solid surface material. Aggregate flow and distribution as well as shades of color can vary from product to product creating natural characteristics. Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor does the omission of any brand name cleaner imply inadequacy. Many products named are regional in distribution, and can be found in local supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that all products should be used in strict accordance with package instructions. Dimensions - Front and Top Views FL-1H shown FL-1L is similar 7-3/4" (197mm) 22" (559mm) 30" (762mm) 37-3/4" (959mm) 36" (914mm) 30" (762mm) 34" (864mm) 12-1/4" (311mm) 30" (762mm) 37-3/4" (959mm) 32" (813mm) 30" ADA (762mm) 34" ADA (864mm) 12-1/4" ADA(311mm) ADA COMPLIANT FL-1H FL-1L Bradley Corporation • 215-1511 Rev. D; EN 07-808 5/30/07 FL-1H, FL-1L Installation 4 5/30/07 Bradley Corporation • 215-1511 Rev. D; EN 07-808 Dimensions - Side Views 4-5/8" (117mm) 28" (711mm) 4-5/8" (117mm) 4-5/8" (117mm) 4-5/8" (117mm) 30" (762mm) 12-1/4" (311mm) 34" (864mm) Rim Height Standard Height 22" (559mm) 19-3/4" (502mm) 14" (356mm) 22" (559mm) 19-3/4" (502mm) 14" (356mm) 22" (559mm) 19-3/4" (502mm) 14" (356mm) 22" (559mm) 19-3/4" (502mm) 14" (356mm) 37-3/4" (959mm) 31" (787mm) Rim Height 30" (762mm) Rim Height Juvenile Height Ages 6–12 34-3/4" (883mm) 9-1/4" (235mm) 8-1/4" (210mm) 33-3/4" (857mm) 26" (660mm) 32" (813mm) Rim Height TAS Height Grades Pre-K through 5 or 6 TAS Height Grades 6 through 8 or 9 10-1/4" (260mm) 35-3/4" (908mm) ADA COMPLIANT ADA COMPLIANT 27" (686mm) 22" (559mm) 19-3/4" (502mm) 14" (356mm) 36" (914mm) Rim Height Not ADA Compliant 30" (762mm) 4-5/8" (117mm) 37-3/4" (959mm) 12-1/4" (311mm) TAS TAS FL-1H FL-1L Installation FL-1H, FL-1L E D D B B AA A A H C W 12-7/8" (327mm) 12-7/8" (327mm) 11" (279mm) 11" (279mm) 10-1/2" (267mm) 3/4" (19mm) 4" (102mm) 5" (127mm) 5" (127mm) 1-3/8" (35mm)33" (838mm) 30" (762mm) 26-3/8" (670mm) 24" (610mm) 18-3/4" (476mm) 17" (432mm) 10" (254mm) 24" (610mm) Recommended 240v/208v or 277v electrical rough-in location (approx. 3" x 6") 1 Rough-Ins CODE DESCRIPTION QTY. A 3/8" Lav Deck Anchors with a Minimum Pull-Out Force of 1,000 lbs. 4 B #10 Wall Anchors/Fasteners for Mounting Trap/Transition Covers 2 H, C 1/2" NPT Hot/Cold Supplies, Stub-Out 2" From Wall 1 D #10 Wall Anchors/Fasteners for Valve Mounting 2 E 110v GFI Protected Electrical Outlet 1 W 1-1/2" NPT Drain, Stub-Out 2" from Wall 1 RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FOR CODES A–E, H, C...
Dieses Handbuch ist für folgende Modelle:Plumbing - FREQUENCY FL-1L (562.27 kb)