Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
. . Step 3: Mount frame to wall 1. Loosen, but do not remove the bottom three access panel screws. 2. Remove the two top access panel screws and washers securing the access panel to the frame and remove the access panel (see Figure 3). 3. Position the frame with Terreon® End Caps attached, against the wall, ensuring that it is level. IMPORTANT: Anchoring the frame to a wall that is not flat may cause the frame to bend. If necessary, install shims to compensate for wall distortion. 4. Ensure that the back of the frame is flat against the wall. If wall is not flat, insert shims behind the frame to ensure that it will not bend when anchored. 5. Once you have positioned the frame such that it is level and flat against the wall or shimmed, use the 3/8" bolts and washers to mount the frame to the wall. FRAME STAINLESS STEEL 3/8" BOLTS AND WASHERS (6) PLACES TERREON® END CAP RIGHT TERREON® END CAP LEFT 1/4" - 20 SCREWS AND FINISHING ACCESS PANEL WASHERS (5) PLACES FRONT VIEW Figure 3 8/23/07 Bradley Corporation • 215-1510 Rev. D; ECN 07-815 AND WASHER BOWL1/4"-20 x 1/2" PAN HEAD Express® Lavatory System - MG Series with Battery Infrared Control Installation Instructions MG-2/BIR3 Installation Instructions continued . . . Step 4: Install bowl assembly IMPORTANT: See Figure 4 below when installing the bowl assembly. If the fixturehas soap option, refer to the soap system installation manual 215-1585 before installing the bowl assembly. 1. With someone to assist you, place the bowl assembly squarely onto the frame being careful not to pinch tubing between bowl and frame. 2. Attach the front of the bowl assembly to the frame using the two 1/4-20 x 1/2" pan-head screws and washers provided. Do not tighten screws at this time. IMPORTANT: When bolting the bowl assembly to the wall, do not overtighten the bolts. Overtightening bolts can damage the Terreon® material. 3. After the bowl assembly is attached to the frame, install the two 3/8" bolts and washers (supplied by the installer) to bolt the bowl to the wall anchors. Do not overtighten bolts. 4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame. Do not overtighten. 5. If necessary, adjust sprayhead body to fit closely to wall by adjusting sprayhead mounting bolts. See Figure 8 on page 13 for sprayhead mounting bolt locations. 3/8" BOLT FRAME 3/8" BOLT SPRAYHEAD AND WASHER SCREWS AND TERREON® TERREON® END CAP (R) (2) PLACES END CAP (L) WASHERS Figure 4 BACK VIEW Bradley Corporation • 215-1510 Rev. D; ECN 07-815 8/23/07 Express® Lavatory System - MG Series with Battery Infrared Control MG-2/BIR3 Installation Instructions 10 8/23/07 Bradley Corporation • 215-1510 Rev. D; ECN 07-815 Installation Instructions continued . . . Step 5: Connecting supply 1. Loosen but do not remove the two mounting screws holding the valve bracket to the frame. Slide the valve bracket up until the larger cutout in the frame’s slot aligns with the screw head (see Figure 5b). Then lift up to remove the valve bracket from the frame. 2. FOR HOT AND COLD SUPPLY: Attach the stop/check to the hot and cold water supply piping from the wall. Connect the flexible hoses to the Vernatherm™ Mixing Valve and to the stop/checks (see Figure 5a). NOTE: The “H” on Vernatherm™ Mixing Valve indicates hot water supply inlet. FOR SINGLE TEMPERED SUPPLY: Attach the stop/check to the 1/2" tempered supply line. Connect the stop/check to the tempered line adapter with the flexible supply hose (Figure 5c). 3. Assemble the P-trap by connecting the 1-1/2" tubular pipe to the tailpiece and to the 1-1/2" drain pipe stubbed out of the wall. 4. Install the strainer on the drain plug opening inside the bowl, and push the strainer firmly into place. Secure the stainer with the screw provided. Figure 5c FLEXIBLE SUPPLY HOSE (TO SOLENOID BRACKET) TO SUPPLY LINE Figure 5a FLEXIBLE SUPPLY HOSE Vernatherm™ THERMOSTATIC MIXING VALVE FLEXIBLE SUPPLY HOSE CONNECT TO 1/2" NPT HOT WATER SUPPLY CONNECT TO 1/2" NPT COLD WATER SUPPLY TEMPERED LINE ADAPTER (S39-685) Figure 5b SLOT IN FRAME VALVE BRACKET MOUNTING SCREW Hot and Cold Supplies Single Tempered Supply Express® Lavatory System - MG Series with Battery Infrared Control Installation Instructions MG-2/BIR3 Installation Instructions continued . . . Step 7: Connecting electrical and supply tubing WARNING: The MG-2/BIR3 must be connected to the 6 VDC battery. Connection to 110VAC may cause personal injury and/or damage to electronics. Connection of leadsother than shown may cause permanent sensor damage. CAUTION: To avoid activating the sprayhead valve, make sure to connect the sensorcable plugs to the circuit board before inserting the batteries into the battery holder. If the cable is connected or disconnected while the batteries are installed, the station will activate and continue running for 75 seconds. 1. Snap the sensor plugs from the sprayhead into the proper valve’s circuit board. 2. Insert the batteries into the battery holders (see Fig...