Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
• Graffiti/Vandalism: If vandals create markings on the panel, Bradley recommends using Motsenbocker’s LIFT OFF® to remove ink and spray paint. Remover #3 is for ink and markers, and Remover #4 is for spray paint. Motsenbocker’s LIFT OFF® can be ordered through Sanitary Maintenance Service Inc. (call 1-800-451-5523 x 425 or visit for ordering information). After cleaning with LIFT OFF®, give the panel a final thorough cleaning with a liquid tub and tile cleaner to remove soil and maintain the glossy finish. NOTE: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products named are regional in distribution and can be found in local supermarkets, department and hardware stores or through your cleaning service. It is emphasized that all products should be used in strict accordance with package instructions. 5/11/04 Bradley Corporation •215-1238 Rev. C; EN 03-813 Express® Lavatory System SS-Series Installation Instructions - For Service Only SS-3/AST/STD, SS-3/AST/JUV Soap Dispenser Maintenance Step 1: Fill soap dispensers The two soap valves will dispense vegetable/coconut oil liquid soaps, synthetic detergents, viscous lotion soaps, and antiseptic solutions. A 10-15% concentration is recommended for vegetable or coconut oil liquid soaps. Synthetic detergents, lotion soaps, and antiseptic soaps require no dilution. 1. Using two screwdrivers (or similar tool), push up on the release tabs located beneath each soap dispenser and pull out the soap tanks from the sprayhead (see Figure 8a). 2. To remove packing dust, rinse out each soap tank with hot water. Shake water out thoroughly and allow to dry. 3. Pour the soap into each soap tank's filler hole (see Figure 8b). 4. After each soap tank is filled, position the soap tanks into the sprayhead openings and push into place. Figure 8a Figure 8b (2) SOAP DISPENSER VALVE S09-007 (2) SOAP TANK 133-107 (GRAY) 133-131 (PUTTY) 133-131A (COAL) FILLER HOLE Bradley Corporation •215-1238 Rev. C; EN 03-813 5/11/04 13 Express® Lavatory System SS-Series SS-3/AST/STD, SS-3/AST/JUV Installation Instructions - For Service Only Soap Dispenser Maintenance continued . . . Step 2: Change soap type 1. Pour out all of the soap from the dispenser. 2. Rinse the soap dispenser with hot water several times until all of the residue is removed, and pump the valve until clean water appears. 3. Rinse the dispenser with ethyl alcohol and allow to air dry. 4. After the dispenser is dry, pour the new soap into the soap dispenser. Step 3: Cleaning Instructions Regular cleaning of the soap dispenser is recommended to ensure optimum performance and maximum service life. Cleaning the soap dispenser monthly to remove soap residue, dirt, and other accumulations should become a regular part of your washroom cleaning routine and general maintenance program. IMPORTANT: Do not use abrasive cleansers to clean the soap tank. Abrasive cleaners can mar the surface. Clean exterior: Use warm water and soap to clean the exterior of the soap dispenser. Dry with a soft cloth. Clean interior: Inspect the interior of the soap tank for residue or coagulation of soap. If necessary, clean the soap tank according to the following procedure: 1. Pour out any remaining soap in the tank. 2. Fill the tank half-full of hot water and shake the tank to dislodge the soap residue. 3. Empty the water from the container and repeat steps 1 and 2 until the soap container is clean. NOTE: If rinsing alone does not remove the soap residue, place a small chain (24 inches long) into the soap tank with hot water and shake the container until the chain dislodges the residue. Then remove the chain and rinse out the soap tank. Clean internal components: To clean the internal components of the soap dispenser, pump hot water through the soap dispenser until a clean flow of water comes out of the valve. Check Valve Troubleshooting If water just dribbles or does not flow from sprayhead: 1. Close the stops and check the valves that supply water to the lavatory system. 2 Inspect the stop/check valves for proper installation. 3. Remove the flexible hoses from the stop/check valves and clean the strainers, if necessary. If water sprayhead delivers all hot or cold water: 1. Close the stops and check the valves that supply water to the lavatory system. 2. Inspect the stop/check valves for proper installation. 3. Remove the flexible hoses from the stop/check valves and clean the strainers, if necessary. 4. Inspect mixing valve for proper installation (see Vernatherm valve on page 19). • A red marking indicates the hot inlet. 5/11/04 Bradley Corporation •215-1238 Rev. C; EN 03-813 Express® Lavatory System SS-Series Installation Instructions - For Service Only SS-3/AST/STD, SS-3/AST/JUV Assembly of Components SPRAYHEAD COVER/SHELF (part number varies with color of unit—contact your local ...
Dieses Handbuch ist für folgende Modelle:Plumbing - EXPRESS SS-3/AST/JUV (261.6 kb)