Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: HP Dateigröße: 135.26 kb Dateiname: 75c32db7-1404-4022-ab2b-88e1c4fa2e56.pdf Unterrichtssprache:

3-phase 3450 184JM 1-. 165 5571-95 7.5 230/460 VAC, 60 Hz. 3-phase 3450 184JM 1-. 150 5572-95 5 230/460 VAC, 60 Hz. 3-phase 3450 184JM 1-. 130 NOTE: Driver data is subject to change without notice, see label on driver for actual specifications. (*) Standard NPT (female) pipe thread Performance Chart GPM of Water at Total Head in Feet Max. Model HP 60 70 80 90 100 110 120 130 140 150 Head† 4445-95 3 805525-------85 ft. 4446-95 3 805525-------85 ft. 5572-95 5 * 115 100 80 50 -----110 ft. 5571-95 7.5 * * 140 125 110 90 70 40 --140 ft. 5570-95 10 * * * 162 150 135 120 95 70 40 160 ft. (*) Operation of pumps beyond range indicated will result in reduced pump life, pump damage and/or motor damage. (†) Shut-off; convert to psi, multiply by specific gravity and divide by 2.31 Installation 1. (5570 series pumps) Remove shipping fixture (Ref. No. 19) that holds the drive shaft to the base before installing pump. 2. Pump must be installed with its base supporting the entire weight of the pump. CAUTION Mounting brackets are not designed to support the pump’s weight. Brackets are designed to prevent tipping. 3. Position pump in tank or reservoir. Position mounting brackets, align pipe clearance hole with pump discharge outlet. (4445 series pumps) 4. Assemble one piece of sponge tape (Ref. No. 25) to each clamp bracket (Ref. No. 24). Attach clamp brackets to mounting brackets with fasteners provided (Ref. Nos. 26 and 27). This will fix the column (Ref. No. 3) in position. (5570 series pumps) 4. Adjust lower fasteners (Ref. No. 4) to bottom of mounting brackets. Secure pump to mounting brackets with upper fasteners (Ref. No. 4). 5. Secure mounting brackets to tank or reservoir. Install an appropriate fastener in each hole or slot provided. 6. Install the balance of the system. 5570-250-00 03/2006 Specifications Information and Repair Parts Manual 4445-95, 4446-95, 5570-95, 5571-95 and 5572-95 Vertical Sealless Sprayer/Washer Pumps Maintenance WARNING Make certain that unit is disconnected from power source before attempting to service or remove any component. IMPELLER/MOTOR REPLACEMENT Refer to Figure 2, and 3. 1. Remove unit from the tank or reservoir. 2. Remove fasteners (Ref No. 8) and washers if present (Ref. No. 7) that connect the volute base (Ref. No. 17) to the volute cover (Ref. No. 10). 3. Remove volute base, and gasket (Ref. No. 16). 4. Place an allen wrench through the slot in the top of the column and into one of the socket head screws of the shaft coupling. Rotate impeller counterclockwise until allen wrench stops against side of slot. Remove nut (Ref. No. 15) and then impeller from drive shaft by rotating each counterclockwise. IMPORTANT: Care should be taken to insure that same number of shim washers (Ref. No. 9), if present, is replaced behind impeller as were removed. These shim washers are located directly behind the impeller. Shim washers may or may not be present depending on assembly clearances. 5. Remove allen wrench from slot and then re...

Herunterladen

Geben Sie zwei Ziffern: