Insert the depth stake assembly in front of spacer (under the tine shield) and up through the tine shield assembly as shown in Figure 3. 3. Insert clevis pin through the tine shield and the second hole from top of the depth stake. Secure with hairpin clip. 4. Insert hex bolt into the top hole of the depth stake assembly. Place flat washer on hex bolt and thread “T” knob onto the hex bolt. See Figure 3. Tighten securely. 5. Tip the tiller back down so it rests on the depth stake (transport pos

It is engineered to minimize the hardest work in the vegetable or flower garden, to till the soil for planting and cultivating, and to perform many other useful labor saving tasks in the garden. With the proper amount of care and maintenance, this machine will provide the owner with many years of service. CONTROLLING SPEED AND TILLING DEPTH: 1. Depth Stake Adjustment: The depth stake acts as a brake for the tiller and controls the depth and speed at which the machine will operate. Remove the c

See figure 12. For cultivation, reduce the tine width to 14 inches by removing the outer tines completely. See figure 13. № 0 0 9 0 0 o & CULTIVATING 0 o o o a o o o o o a oj FIGURE 13. CLUTCH CONTROL ADJUSTMENT To adjust the clutch control, refer to the “Final Adjustment” section of assembly instructions. CARBURETOR ADJUSTMENT A WARNING: If any adjustments are made to the engine while the engine is running (e.g. carburetor), disengage all clutches and tines. Keep clear of

Adjustment is needed if the tines or wheels seem to hesitate while turning, but the engine maintains the same speed. To adjust to the tension on the belt, refer to clutch adjustment information in step number 25 of the Assembly Instructions. CARBURETOR ADJUSTMENT A WARNING: If any adjustments are made to the engine while the engine is running, (e.g. carburetor), disengage all clutches and tines. Keep clear of all moving parts. Be careful of heated surfaces and muffler. Never make unnecessary

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No. 769-003595 (November 2, 2007) To The Owner 1 Thank You Thank you for purchasing a Garden Tiller manufactured by Cub Cadet LLC. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, ope

REAR TINE TILLER Model Number 448 (21A-448-100) Important: Read Safety Rules and Instructions Carefully Thank you for purchasing an American-built product. WARNING: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained i

Move machine to another area. Wait 5 minutes before starting the engine. i. Never store the machine or fuel container inside where there is an open flame, spark, or pilot light (e.g. furnace, water heater, space heater, clothes dryer, etc.) j. To reduce a fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil fuel spillage and remove any fuel soaked debris. k. Allow machine to cool at least 5 minutes before storing. OPERATION 1. Do not put hands and feet near rot

Bell. .340” I.D. x .872” O.D. 6. 720-0274 Grip-Handle 31. 711-1036 Spec. Hex Nut 7. 712-0287 Hex Nut 1/4-20 Gr.2 32. 736-0119 L-Wash. 5/16” I.D. 8. 726-0135 Cap Speed Nut 33. 710-3008 Hex Bolt 5/16-18 Gr. 5 9. 686-0083 Clutch Handle Assembly 34. 786-0129 Cable Guide Bracket 10. 720-0269 Grip-Clutch 35. 710-0604 Hex Wash Screw 5/16-18 x .62” 11. 710-0641 Hex Bolt 1/4-20 x 2.25” Lg. Gr.5 36. 710-0602 Hex Wash. Hd. TT-Tap Scr. 12. 731-1645A Clutch Handle Holder 37. 738-0934 Shdl. Bolt 5/16-1

Figure 5–9: Reverse drive belt removal. Figure 5–10: Reverse drive belt removal. 6 Off-Season Storage If the tiller will not be used for a period longer than 30 days, the following steps should be taken to prepare the tiller for storage. 1. Clean the exterior of engine and the entire tiller thoroughly. Lubricate the tiller as described in the lubrication instructions. 2. We do not recommend the use of pressure washers to clean your unit. They may cause damage to electric components, spindles, pu

BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No. 769-03793 (January 10, 2008) RT 65 Gear Case Assembly 52 35-"^ 14 14 11 16 * 28 2 RT 65 Gear Case Assembly Ref. Part Number Description 1. 611-04074 Wheel Shaft Assembly: 33T 2. 611-0021 Tine Shaft Assembly: 18T 3. 611-0128 Jack Shaft Assembly 4. 611-0129 Input Shaft Assembly 5. 617-0058 Reverse Idler Gear Assembly: 30T 6. 617-0059 Tine Idler Gear Assembly: 30T 7. 617-0060 Tine Input Sprocket Assembly: 9T 8. 617-