Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
If the blade does not turn when you squeeze the throttle trigger of the powerhead, make sure the attachment is fully inserted into the coupler. Always release the throttle trigger and allow powerhead engine to return to idle speed when not cutting. The blade should not turn while the engine is running at idle. If the blade turns at idle, do not use your unit. Refer to the CARBURETOR ADJUSTMENT section of the powerhead manual or contact your authorized service dealer. S Maintain good firm footing while using the 4 o’clock blade unit. Do this by planting feet firmly in a comfortable apart position. S Cut while swinging the upper part of your body from left to right. S As youmoveforward to thenext area to cut, be sure to maintain your balance, and footing. RECOMMENDED CUTTING POSITION o’c2lock Cut using the 2 o’clock to 4 o’clock position of the 7 WARNING: The operator or others must not try to clear away cut material with the engine running or the blade turning to avoid serious injury. Stop engine and blade before removing materials wrapped around blade or shaft. MAINTENANCE WARNING: Always stop unit and disconnect spark plug wire before performing maintenance. CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service dealer for replacement of damaged or worn parts. S Blade Shield - --Discontinue use of brushcut ter attachment if shield is damaged. CHECK FOR LOOSE FASTENERS AND PARTS S Blade nut S Fasteners INSPECT AND CLEAN UNIT AND DECALS S After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent. S Wipe off unit with a clean dry cloth. BLADE MAINTENANCE WARNING: The blade will continue to spin after the engine stops or after the throttle trigger has been released. To avoid serious injury, make sure the blade has stopped coasting and disconnect the spark plug before performing work on the blade. WARNING: Always replace a blade that is bent, warped, cracked, broken, or damaged in any other way. Never attempt to straighten and reuse a damaged blade. Use only specified replacement blade. Wear protective gloves when handling or performing maintenance on the blade to help avoid injury. S Check blade for flatness periodically. Lay the blade on a flat surface to inspect for flatness. Throw away a blade that is not flat. SERVICEANDADJUSTMENTS BLADE REPLACEMENT 3. While holding the screwdriver in position, remove blade nut by turning clockwise as WARNING: The blade will continue to you are facing the nut. spin after the engine stops or after the throttle 4. Remove both washers and the blade trigger has been released. To avoid serious from the blade shaft. Leave the dust cup injury, make sure the blade has stopped on the gearbox. coasting and disconnect the spark plug before 5. Install new blade and retaining washer onto performing work on the blade. the threaded shaft extending from the gearbox (blade must be between the dust cup WARNING: Wear protective gloves when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is not moving. 1. To remove the blade, align hole in the dust cup with the hole in the side of the gearbox by rotating the blade. 2. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loosening the blade nut. Screwdriver and the retaining washer). Make sure the raised part of the retaining washer is facing the gearbox, and the raised area fits into the hole in the center of the blade. Gearbox Shield Retaining Washer Cupped Washer Nut BladeDustCupThreadedShaft 8 6. Place the cupped washer onto the shaft. 8. Tighten blade nut firmly with a wrench Make sure the cupped side of the washer while holding screwdriver in position. is toward the blade. 9. Remove the screwdriver. 7. Install blade nut by threading onto the 10. Turn blade by hand. If the blade binds shaft counterclockwise as you are facing against the shield, or appears to be unthe nut. even, the blade is not centered, and you NOTE: Make sure all parts are in place as illus-must reinstall. trated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer. STORAGE WARNING: Perform the following steps after each use: S Allow attachment and gearbox to cool before storing or transporting. S Store attachment with blade shield in place. Position attachment so that any sharp object cannot accidentally cause injury. S Store the attachment in a dry, well ventilated area out of the reach of children. SEASONAL STORAGE Prepare attachment for storage at end of season or if it will not be used for 30 days or more. If your brushcutter attachment is to be stored for a period of time: S Clean the entire attachment. S Inspect the blade shield area and clean any dirt, grass, leaves, or debris that has collected. Inspect the blade and blade shield; replace a blade that is bent, warped, cracke...
Dieses Handbuch ist für folgende Modelle:Gartengeräte - U4000C (139.76 kb)