Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Tighten screw securely. A CAUTION: Petroleum solvents, such as kerosene, are not to be used to clean cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry cartridge. COOLING SYSTEM (See Fig. 14) Your engine is air cooled. For proper engine performance and long life keep your engine clean. • Clean air screen frequently using a stiff-bristled brush. • Remove blower housing and clean as necessary. • Keep cylinder fins free of dirt and chaff. CYLINDER FINS MUFFLER* !';( FIG. 14 FIG. 12 11 CUSTOMER RESPONSIBILITIES MUFFLER Do not operate tiller without muffler. Do not tamper with exhaust system. Damaged mufflers or spark arresters could create a fire hazard. Inspect periodically and replace if necessary. If your engine is equipped with a spark arrester screen assembly, remove every 50 hours for cleaning and inspection. Replace if damaged. SPARK PLUG Replace spark plugs at the beginning of each tilling season or after every 50 hours of use, whichever comes first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” on page 3 of this manual. TRANSMISSION Your transmission is sealed and will not require lubrication unless serviced. CLEANING Do not clean your tiller when the engine and transmission are hot. We do not recommend using pressurized water (garden hose, etc.) to clean your unit unless the gasket area around the transmission and the engine muffler, air filter and carburetor are covered to keep water out. Water in engine will shorten the useful life of your tiller. • Clean engine, wheels, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax. SERVICE AND ADJUSTMENTS A CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER TO ADJUST HANDLE HEIGHT (SEE FIG* 15) Factory assembly has provided lowest handle height. Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil. • If a higherhandle height is desired, loosen the four nuts securing handle panel to engine brackets. • Slide handle panel to desired location. • Tighten the four nuts securely. ENGINE BRACKETS HANDLE PANEL NUTS (ALSO 2 ON LEFT SIDE OF TILLER) FIG. 15 TINE ARRANGEMENT You router tines can be assembled in several different ways to suit your tilling or cultivating needs. CAUTION: Tines are sharp. Wear gloves or other protection when handling tines. NORMAL TILLING - 26" PATH (See Fig. 16) • Assemble holes “A” in tine hubs to holes “B” in tine shaft. MID-WIDTH TILLING - 24" PATH (See Fig. 17) • Assemble holes “A” in tine hubs to holes “C” in tine shaft. NARROW TILLING/CULTIVATING -12-3/4" PATH (See Fig. 18) • Remove outer tines. 12 NOTE: When reassembling outer tines, be sure right tine assembly (marked “R”) and left tine assembly (marked “L”) are mounted to correct side of tine shaft. SERVICE AND ADJUSTMENTS TINE OPERATION CHECK (See Fig. 19) A WARNING: Disconnect spark plug wire from sparkplug to prevent starting whiie checking tine operation. For proper tine operation, forward tine control lever must be against control body and all slack removed from inner wire of control cable when control is in the “OFF” (up) position. If lever and cable are loose, loosen cable clip at lower end of cable. Pull up on cable to remove slack, without extending spring on end of cable, and retighten cable clip. FINAL CHECK “OFF” POSITION • With tine control “OFF” (up), push down on handle to raise tines off the ground. • Slowly pull recoil starter handle while observing tines. Tines should not rotate. • If tines rotate, inner wire of control cable is too tight which is extending lower spring and engaging tines. Loosen cable clip and push down on cable only enough to relieve spring tension, Tighten cable clip, • Recheck in “OFF” position and adjust if necessary. FINAL CHECK “ON” POSITION • With tine control “ON” (held down to handle) push down on handle to raise tines off the ground. • Slowly pull recoil starter handle while observing tines. Tines should rotate forward. • If tines do not rotate, inner wire of control cable is too loose. Loosen cable clip and pull cable up to remove slack and retighten clip. • Recheck in “ON” position and adjust if necessary. NOTE: If “ON” position check required adjustment, recheck “OFF” position adjustmentto insure tines do not rotate when control is “OFF” (up). TO REMOVE BELT GUARD (See Fig. 20) • Remove two (2) cap nuts and washers from side of belt guard. • Loosen (do not remove) tine shield nut on underside of tine shield. • Pull belt guard out and away from unit. • Replace belt guard by reversing above procedure. Be sure slot in bottom of belt guard is under head of tine shield bolt and all nuts are tightened securely. TO REPLACE V-BELTS (See Figs. 21...