Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
STARTING A WARM ENGINE Pull starter rope sharply while squeezing throttle trigger until engine runs. NOTE: Normally, the warm starting procedure can be used within 5- --10 minutes after the unit is turned off. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit. STARTING A FLOODED ENGINE Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter handle repeatedly while squeezing throttle trigger until engine starts and runs. This could require pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723. OPERATING THE COUPLER This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are: MODEL: Edger ....................... PP1000E Cultivator .................... PP2000T Blower ...................... PP3000B Brushcutter .................. PP4000C 13 WARNING: Always stop unit and disconnect spark plug before removing or installing attachments. REMOVING PRUNER ATTACHMENT, LINE TRIMMER ATTACHMENT, OR OTHER OPTIONAL ATTACHMENTS CAUTION: When removing or installing at tachments, place the unit on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. Attachment CouplerKnobLOOSEN TIGHTEN 2. Press and hold the locking/release button. Locking/Release Button Attachment Upper Shaft Coupler 3. While securely holding the engine end shaft and extension shaft, pull the attachment straight out of the extension shaft coupler. 4. Repeat steps to remove extension shaft from coupler on engine end shaft. INSTALLING OPTIONAL ATTACHMENTS 1. Remove the shaft cap from the attachment (if present). 2. Position locking/release button of attachment into guide recess of coupler on engine end shaft. 3. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 4. Before using the unit, tighten the knob securely by turning clockwise. Primary Hole Coupler Guide Recess Locking/ Upper Release Attachment Shaft Button WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before operating the unit. All attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual. Using the wrong hole could lead to serious injury or damage to the unit. Locking/ReleaseButtoninPrimaryHole INSTALLING ATTACHMENT HANGER An attachment hanger is provided for storage when attachment is not in use. To install hanger on attachment: 1. Remove the shaft cap from the attachment (if present) and discard. 2. Press and hold the locking/release button. 3. Push hanger onto the attachment until the locking/release button snaps into the hole. OPERATING INSTRUCTIONS It is recommended that the engine not be operated for longer than 1 minute at full throttle. OPERATING INSTRUCTIONS FOR PRUNER ATTACHMENT OPERATING POSITION EyeprotectionALWAYSWEAR: LongpantsHeadprotectionHeavyshoes DANGER: Do not extend arms above shoulders while pruning. Do not stand be neath branch being cut. WARNING: Always wear head, eye, hearing, foot and body protection to reduce the risk of injury when operating this unit. When operating unit, clip shoulder strap onto clamp, stand as shown and check for the following: S Extend your left arm and hold assist handle with your left hand. S Hold throttle grip with your right hand with finger on throttle trigger. S Keep engine end below waist level. 14 S Keep shoulder strap pad centered on your left shoulder and danger sign centered on your back. S Maintain full weight of tool on your left shoulder. Always release the throttle trigger and allow the engine to return to idle speed when not pruning. To stop engine: S Release the throttle trigger. S Push and release the engine ON/STOP switch. PRUNING WARNING: Be alert for and guard against kickback. Do not allow the moving chain to contact any other branches or objects at the nose of the guide bar when pruning. Allowing such contact can result in serious injury. IMPORTANT POINTS S Work slowly, keeping both hands firmly gripped on the pruner. Maintain secure footing and balance. S Plan cut carefully. Check direction branch will fall. S Watch out for springpoles. Springpoles are small size limbs which can catch the chain and whip toward you or pull you off balance. Use extreme caution when cutting small size limbs or slender material. S Watch out for branches immediately behind the branch being pruned. If the chain hits the rear branch, damage to the unit may occur. S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the pruner when the tension in the wood fibers is released. S Keep a clear work area. Freq...
Dieses Handbuch ist für folgende Modelle:Gartengeräte - 966423701 (406.21 kb)