Stimmen - 5, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
While operating the Tiller in preparing the ground, the operator needs only to press down on the handles for a deeper tilling action. Remember a downward pressure on the handles results in a slow down of the forward movement and a deeper tilling action. An upward pressure on the handles results in an increase in the forward movement and a shallow tilling action. LET THE DEPTH BAR DO THE WORK Your Tiller is scientifically designed to prepare the soil for planting with a minimum of effort. Do not attempt to till when the soil is very wet as this may cause lumps which are difficult to work up. If the soil is extremely hard and dry you may find it desirable to cross-till to obtain the depth you want. On the first pass, till across the plot, and on the second pass, till in the direction in which the rows will run. When operating your Tiller for the first time, we suggest you try it for a short time to get the “feel”. You will want to find the most comfortable handle position, the correct location of the depth bar for ease of operation, the engine speed best suited to your soil condition. You will soon find the correct pressure to apply to the handles. Experiment with the clutch lever, and notice the immediate response from “tickling” the clutch. You will find this very desirable when doing close cultivation with the tiller. DISTANCE BETWEEN BELT STOP & BELT SHOULD BE APPROXIMATELY 1/8" Check for proper clutching action. Set the belt stops as near as possible to the belts when they are engaged. Make sure that the belts stop turning when the clutch lever is released and do not slip when gripped. If adjustment is needed, loosen the roung Allen screws in the wire clamps and reposition the control cables. FURROW OPENER A furrow opener shovel is available which mounts on the depth bar. You will find this shovel very handy for digging furrows for crops such as potatoes that are planted in rows. When installing the furrow opener, turn the depth bar upside down and bolt to the tool holder with the carriage bolts, washers and nuts supplied. Remove the stop piste from between the support assemblies on the Tiller and install the extension support assembly with the same hardware. The depth bar is then positioned in this extension, the clamp installed and these pieces secured with the pin and clip supplied. Ref. Let. Part No. Description A 8271503 Tool Holder B 118287 Extension Support Assembly C 103010 8” Furrow Opener D 703002 Carriage Bolt, 3/8”-16 x 1-1/4’lg. E 719001 Plain Washer, 3/8” F 717003 Hex .Nut, Full, 3/8”-16 G 118053 Pin H 8161045 Spring Clip J 704001 Plow Bolt TINE EXTENSION SET The tine extension set consits of a left hand and right hand tine assembly. These additional extensions will allow an increase from the standard 22-1/2” tilling width to a width of 32-1/2” as shown in Figure 5. To install the extension tines, place long hubs of extension tines over hubs of tines previously installed, and secure with pin and spring clip. Be sure the extension tines are so mounted that the sharp edges of the tines on top face forward. Figure 5. Ref. Let. Part No. Description A 105288 Extension, L.H. Tine Assy. Complete B 105286 Plate Assy., Tine Extension C 105289 Extension, R.H. Tine Assy. Complete D 8152001 L.H. Tine Blade E 8152002 R.H. Tine Blade F 706009 Hex. Capscrew, 7/16”-20 x 1-1/4” lg. G 717512 Hex. Nut, Full, 7/16”-20 5 Ref. Let. Part No. Description Ref. Let. Part No. Description A 170879 Body Assembly X 118467 Handle, R.H. В 170360 Scraper Y 722011 Cotter Pin 3/16”xl” С 705004 Hex Hd. Cap Screw 3/8”-16 N.C. Z 715061 Hex Hd. Cap Screw 3/8”-16 N.C. x. x 3/4” lg. 1” lg. D 720002 Lock Washer, 3/8” AA 8061108 Clip, Cable E 717013 Hex Nut, Full 3/8”-16 AB 118298 Cover Handle Bar F 118030 Wheel & Tire Assembly AC 705025 Hex Hd. Cap Screw l/4”-20 N,C. x. G 118132 Bushing, Wheel 1-1/2” lg. H 719004 Plain Washer, 1/2” AD 720003 Lock Washer, 1/4” J 705037 Hex Hd. Cap Screw l/2”-13 N.C. x AE 717513 Hex Nut, Full Lock, l/4”-20 3-1/4” lg. AF 118235 Throttle Control Assembly К 717017 Hex Jam Nut l/2”-13 AG 714016 Screw, Self Tapping No. 10-24 L 118207 Stop Plate AH 118449 Grip, Clutch-Reverse M 705009 Hex Hd. Cap Screw 3/8”-16 N.C. x AJ 719010 Plain Washer No. 10-24 x 1/2” 1-1/2” lg. AK 172924 Control Wire N 717003 Hex Nut 3/8”-16 AL 118495 Spring P 118081 Bar-Depth AM 161092 Clamp, Wire Q 118447 Clamp - AN 714016 Set Screw No. 10-24 x 1/2” R 105249 Pin AP 118431 Grip, Clutch-Forward S 8161045 Spring Clip AQ 106558 Grip, Handle Bar T 170359 Cover AR 717005 Hex Nut Full, l/4”-20 N.C. Ü 715067 Screw Washer Hd. Thread Forming AS 715055 Hex. Hd. Cap Screw, 3/8”-16 N.C. 1/4”-20 x 1-1/4” V 121037 Spring AT 118237 Control Housing Assembly w 118466 Handle, L.H. DRIVE and TINES 165044 Belt Stop 106707 Belt Stop Ref. Let. Part No. Description A Engine B & S 5 H.P. B 705020 Hex Hd. Cap Screw 5/16”-18 N.C. x 2” lg. C 719002 Plain W...