Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Always return the handle by hand - DO NOT RELEASE THE HANDLE WITH THE ROPE EXTENDED. To stop the engine, pull the throttle lever all the way back. BEFORE OPERATING 1. The depth bar setting determines the depth of tilling. To till 4 to 6 inches deep, install the bar mounting pin in the second or third hole from the TOP. Simply pull out the hairpin cotter to change pin location. Be sure to install the bar with the digging tip as shown. THE DEEPER THE DEPTH BAR IS SET INTO THE SOIL, THE DEEPER THE TINES WILL DIG. 2. Check to be sure that the wheels are mounted in the LOWER holes of the frame legs as shown. 3. The standard tine arrangement shown allows a tilling width of 20-1/2 inches. The two outer sets of tines can be removed to narrow the width to 12 inches if desired. Simply pull out the cotter pins and remove the mounting pins. Tine assemblies are left and right hand. Switch the two inner tines for an 8-1/2 inch wide path. Switch the outer tines and add them to change the width to 16 inches. Always be sure when rearranging tines that the sharpened edges face forward. A set of tine extensions is available to extend the width to 29-1/2 inches. See your Simplicity dealer. -4-20-1/2" (STANDARD)->■ OPERATION After starting, move the throttle lever to 3/4 forward. To engage the tiller drive, squeeze the clutch lever. To stop, merely release the clutch lever. Use the depth bar to furnish the necessary drag rather than pulling back on the handles. Push DOWN on the handles to LOWER the depth bar, slowing forward speed, and deepening the bite of the tines. Upward thrust on the handles increases forward speed and raises tilling depth. LET THE DEPTH EAR DO THE WORK . The Roticul is scientifically designed to cultivate the soil with a minimum of physical effort on the part of the operator. When operating for the first time, proceed slowly and carefully to get the “feel”. Experience will determine the best speed for your requirements, the correct handle pressure and depth bar setting. Experiment with the clutch lever, using ¿he quick response for positive control in close areas. Do not till when the soil is very wet. This causes lumps which are difficult to work up. If the soil is extremely hard and dry it may be desirable to cross-till an area at shallow depth first, then till in the direction of planting rows on the second pass at the final depth. A furrow opener shovel is available from your Simplicity dealer for use in digging furrows for crops which are planted in rows, such as potatoes. See “Accessories”. TROUBLESHOOTING IF ENGINE FAILS TO START, check the following: 1. Fuel tank is full. 2. Throttle lever is set to 1/2 open. 3. Spark plug cable is securely connected. 4. Choke plunger is pulled out to “CHOKE” position or in “OFF” position (in) if engine appears to be flooded. To clear a flooded engine, push the choke in and pull the starter rope several times to clear the excess fuel. IF BELT SLIPPAGE OCCURS, check the following: 1. Belt may be stretched or worn excessively. 2. Belt may be greasy or oily. If so, use Energine or a similar cleaning fluid on a rag to clean. An alternate method is to sprinkle a handful of Drizit or Kitty-Litter compound on the belt while running. 3. Pulleys may be misaligned. 4. Belt Tension may be too tight. (See “Adjustments.”) 5 ADJUSTMENTS BELT STOPS: Make sure the belt stops are as near as possible to the belt when running. Loosen the stop mounting bolt to adjust position or bend the stops where necessary to within 1/8 inch of belt when running. CLUTCH ADJUSTMENT: Check for proper clutch engagement. Belt must not be running when the clutch lever is released and must not slip when lever is engaged. If adjustment is required, loosen the round head screw in the control wire clamp and remove excess slack in the wires. Tighten the screw securely. DRIVE BELT SLACK: After some use, the drive belt may stretch so that clutch adjustment cannot be made at the control wire clamp. If this occurs, remove the engine mounting nuts, remove the shims shown and install one or more of them under the engine. Tighten the mounting nuts securely. MAINTENANCE To keep your Simplicity Roticul at peak operating efficiency, these maintenance procedures must be followed regularly: 1. Read the engine owner’s manual thoroughly. Always check the engine oil level before starting. Add 10W-30 grade MS oil until level with the top of the tiller neck. Change crankcase oil and re-oil the air cleaner foam element every 25 hours of operation, more often under extremely dusty or dirty conditions. 2. Turn the screw on the air cleaner cover counterclockwise to loosen. Remove the cover. Wash the foam air cleaner element in Kerosene or liquid detergent and dry it thoroughly. Saturate it with engine oil, squeeze out the excess and reinstall. 3. Clean and re-gap the spark plug every 100 hours of operation. Gap to .030 inches. DO NOT clean plug by sandblasting. Grease the plug threads before re...
Dieses Handbuch ist für folgende Modelle:Gartengeräte - 340 (982.83 kb)