Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
5.1 Rear Handle .......................................................................................................................... 6.2 Sound pressure level (in accordance with EN ISO 11806:1997, ISO 7917:1987) ............................................................ 99 Sound power level (in accordance with ISO 10884) ...................................................................................................... 113 5 6 UNPACKING INSTRUCTIONS ¦ Carefully remove the product from the carton. ¦ Inspect the product to make sure no breakage or damage occurred during carriage. ¦ Do not discard the packing material until you have inspected and operated the product. PACKING LIST FOR OWNER’S KIT ¦ Grass deflector ¦ Blade guard ¦ Tri-Arc blade ¦ Shoulder strap ¦ Silencer guard, torque wrench and screws ¦ Front “J” handle ¦ Holding pin ¦ Spanners - 13 mm (1/2 in) and 16 mm (5/8 in) ¦ Fixings ¦ Operator’s manual FEATURES Fig. 1 THROTTLE TRIGGER STARTER GRIP ENGINE HOUSING FRONT “J” HANDLE IGNITION SWITCH TRI-ARC BLADE BLADE GUARD SHAFT STRAP HANGER SHOULDER STRAP GEAR HEAD THROTTLE GRASS DEFLECTOR INTERLOCK CUTTING LINE LINE CUTOFF BLADE COUPLER KNOB ASSEMBLY ATTACHING THE POWER HEAD TO THE TRIMMER ATTACHMENT See Figure 2. REMOVING THE ATTACHMENT FROM THE POWER HEAD For removing or changing the attachment: 1. Loosen the knob. 2. Push in the button and twist the shafts to remove and separate ends. ATTACHING THE STORAGE HANGER See Figure 3. There are two ways to hang your attachment for storage. ¦¦¦¦¦ To use the hanger cap, push in the button and place the WARNING: Be certain the knob is fully tightened before operating equipment; check it periodically for tightness during use to avoid serious injury. The trimmer attachment connects to the power head by means of a coupler device. 1. Loosen the knob on the coupler of the power head shaft and remove the end cap from the attachment. 2. Push in the button located on the trimmer attachment shaft. Align the button with the guide recess on the power head coupler and slide the two shafts together. Rotate the trimmer attachment shaft until the button locks into the positioning hole. NOTE: If the button does not release completely in the positioning hole, the shafts are not locked into place. Slightly rotate from side to side until the button is locked into place. 3. Tighten the knob securely. WARNING: Never attach or adjust any attachment while power head is running. Failure to stop the engine may cause serious personal injury. Fig. 2 COUPLER KNOB TRIMMER ATTACHMENT TRIMMER SHAFT POSITIONING HOLE GUIDE RECESS Fig. 3 BUTTON HOLE HANGER CAP hanger cap over end of the lower end attachment shaft. Slightly rotate the cap from side to side until the button locks into place. ¦ ¦¦¦¦¦The secondary hole in the attachment shaft can also be used for hanging. 7 ASSEMBLY FRONT HANDLE See Figure 4. A barrier handle should be used for ensuring the best control and maximising operator safety. 1. Hold the top and bottom clamp snugly in position on the shaft housing so that handle will be located to the operator’s left. 2. Insert the end of the handle between the clamps. 3. Align the bolt holes and push the long bolt (1/4-20 x 1 1/2 in) through the handle side. 4. Place short bolt (1/4-20 x 1 in) through opposite side of clamp. Install flat washer, lock washers and hex nuts to hold the assembly in place. 5. After assembly is complete, adjust the position of the handle for best balance and comfort. 6. Tighten first the long bolt and then the short bolt. 7. Connect the shoulder strap to the strap hanger adjust to a comfortable position. NOTE: Do not attempt to remove or modify the spacer. This spacer limits the upper position of the handle grip. See Figure 4. ATTACHING THE SHOULDER STRAP See Figure 5. 1. Connect the latch on the shoulder strap to the strap hanger. 2. Adjust the strap to a comfortable position. NOTE: To quickly release the product from the shoulder strap, sharply pull the quick release tab. Fig. 4 CLAMP FRONT HANDLE FLAT WASHER LOCK WASHERHEX NUT STRAP HANGER BOLT 1/4-20 x 1 1/2 in. BOLT 1/4-20 x 1 in SPACER CLAMP SHOULDER STRAP LATCH STRAP HANGER QUICK RELEASE TAB Fig. 5 8 9 ASSEMBLY GRASS DEFLECTOR FOR TRIMMER USE BLADE GUARD FOR BRUSHCUTTER USE Fig. 7 Fig. 6 BENT END OF SILENCER GUARD OPENING IN REAR HOUSING SCREWS SILENCER GUARD REAR HOUSING TORQUE WRENCH SILENCER GUARD ASSEMBLY See Figure 6. 1. Remove silencer guard and two screws from the owner’s kit. 2. Attach the silencer guard to the rear housing. NOTE: Make sure the bent end of the silencer guard fits securely into the opening of the rear housing. 3. Install two screws. 4. Tighten screws securely. GRASS DEFLECTOR AND BLADE GUARD USE See Figure 7. NOTE: When converting from brushcutter to trimmer, or trimmer to brushcutter, make sure the correct guard/ deflector is being used. ASSEMBLY BLADE GUARD See Figure 8. 1. Attach the blade guard to the mounting bracket; install the four screws (10-24 x 3/4 in) from t...