Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Replace damaged hose before using applaince. Use onlyvalve/hose/regulator specified by manufacturer. Kinked Hose Normal Hose General Appliance Cleaning • Meat Thermometer: Do not immerse or soak in water. Wash with warm soapy water and wipe dry. • Do not mistake brown or black accumulation of grease andsmoke for paint. Interiors are not painted at the factory (andshould never be painted). Apply a strong solution of detergentand water or use a grill cleaner with scrub brush on insides ofappliance lid and bottom. Rinse and allow to completely air dry. Do not apply a caustic grill/oven cleaner to paintedsurfaces. A black surface improves the appliancesperformance. • Plastic parts: Wash with warm soapy water and wipe dry. Do not use citrisol, abrasive cleaners, degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result. • Painted surfaces: Wash with mild detergent or non-abrasivecleaner and warm soapy water. Wipe dry with a soft nonabrasive cloth. • Cooking surfaces: If a bristle brush is used to clean any of the grill cooking surfaces, ensure no loose bristles remain on cooking surfaces prior to grilling. It is not recommended to clean cooking surfaces while grill is hot. Page 9 Cleaning the Burner Assembly (Continued) 9. Clean inner burner as recommended below, shown E. We suggest three ways to clean the burner tube. Use the one easiest for you. (A) Bend a stiff wire (a light weight coat hanger works well) into a small hook. Run hook through burner tube several times. (B) Use a narrow bottle brush with a flexible handle (do not use a brass wire brush), run the brush through burner tube several times. (C) Wear eye protection: Use an air hose to force air into the burner tube and out the burner ports. Check each port to make sure air comes out each hole. 10. Check burner for damage, due to normal wear and corrosion some holes may become enlarged. If any large cracks or holes are found replace burner. 11. Carefully replace heat shield and control panel assembly . 12. Reattach electrode wire to ignitor. VERY IMPORTANT: Burner tube must re-engage over valve opening. See illustration, shown F. 11. Reattach front legs. Carefully stand the unit upright. 13. Reposition inner liner, cooking basket. Burner (exposed) Burner (exposed) Tube cleaner (see above recommendations) Cooking Basket Cooking Chamber Remove Screws Control Panel Assembly Electrode Wire Valve engaged inside burner tube end correctly (Control panel and heat sheild hidden for clarity) Valve Burner Tube B C D E F CAUTION SPIDER ALERT! VALVE CONTROL PANEL SPIDER WEBS INSIDE VENTURI If you notice that your the appliance is getting hard to light or that the flame isn’t as strong as it should be, take the time to check and clean the venturi’s. In some areas of the country, spiders or small insects have been known to create “flashback” problems. The spiders spin webs, build nests and lay eggs in the the appliance’s venturi tube(s) obstructing the flow of gas to the burner. The backed-up gas can ignite in the venturi behind the control panel. This is known as a flashback and it can damage your the appliance and even cause injury. To prevent flashbacks and ensure good performance the burner and venturi assembly should be removed from the the appliance and cleaned before use whenever the the appliance has been idle for an extended period. BURNER SPIDER AND WEBS INSIDE BURNER Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting appliance. 1. Turn gas OFF at control knob and LP cylinder and disengage regulator from cylinder. 2. Open top cover, remove cooking basket and cooking Chamber, shown A. This will expose the burner from inside, shown B. 3. Wire brush entire outer surface of burner to remove food residue and dirt. 4. Clean any blocked ports with a stiff wire such as an open paper clip. 5. Carefully lay the appliance on its back, with control panel facing up shown C. 6. Disconnect electrode wire underneath appliance, shown C. 7. Remove screws and disengage front legs from appliance. 8. Remove screws and disengage control panel assembly and heat shield from unit, shown D. Remove Front Legs Carefully place unit on its back. Heat Shield Burner Tube A Page 10 Please note that the burner shown is for illustration purposes only. The burner in your product may be different from the one shown. LIMITED WARRANTY LIMITED WARRANTY This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase*. The manufacturer reserves the right to require that defective parts be returned, postage and or freight pre-paid by the consumer for review and examination. SCOPE OF COVERAGE PERIOD O...
Dieses Handbuch ist für folgende Modelle:Gartengeräte - The Big Easy 42804468 (4.41 mb)