Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
Transmission shifting is done by shifting the WHEEL and TINE SHIFT LEVER into the desired position. See Figure 3. 2.1.1 TRANSMISSION POSITIONS: The tiller has five different transmission positions. They are as viewed from the operator’s position, viewed from the left to right as follows: 1. FWD & FWD TIL -(Forward Rotating Wheels and Forward Rotating Tines are engaged). 2. FWD & REV TIL - (Forward Rotating Wheels and Reverse Rotating Tines are engaged). 3. FWD - (Forward Rotating Wheels are engaged). 4. NEU - (Wheels and Tines are disengaged). 5. REV - (Reverse Rotating Wheels). 2.2 PRE-START CHECKLIST Make the following checks and perform services as required before each start up. NOTE: Before checking oil level place 2x4 piece of wood under both wheels to level engine. 2.2.1 CHECK ENGINE OIL and bring level up to full. (Refer to engine manual for oil specifications). 2.2.2 CHECK AIR CLEANER and service according to instructions in engine manual. 2.2.3 CHECK EXTERNAL SURFACES and remove dirt and dust accumulation and clean tines as needed. 2.2.4 CHECK GUARDS to make sure all are in proper position and securely tightened. 2.2.5 FILL FUEL TANK where fumes will be safely dissipated. Refer to engine manual for fuel specifications. 2.3 BRIGGS ENGINE STARTING - STOPPING Know beforehand how to stop the tines, wheel drive and engine in preparation for possible emergencies. The Briggs engine is stopped by moving the engine SPEED CONTROL to the rear to STOP. See Figure 2. MOVE ENGINE SPEED CONTROL TO STOP POSITION STOP ENGINE SPEED: SLOW – TURTLE FAST - RABIT FUEL VALVE FIGURE 2 2.3A HONDA ENIGNE STARTING - STOPPING The Honda engine is stopped by moving the ENGINE KILL SWITCH to the “OFF” position. See Figure 2A. MOVE THE ENGINE KILL SWITCH TO “OFF” FIGURE 2A WHEEL & TINE STARTING - STOPPING When the wheel and tine control is activated, the tines rotate in a rearward or forward direction. With the engine running, shift into the desired transmission position and pull the WHEEL and TINE CONTROL BAIL against the handle bar to start wheel or wheel and tine rotation. Wheel or wheel and tine rotation is STOPPED by releasing the WHEEL and TINE CONTROL BAIL. When the bail is released, rotation should STOP even with the WHEEL and TINE SHIFT LEVER in an engaged position. See Figures 3 and 4. WHEEL & TINE CONTROL REV NEU FWD FWD & REV TILL FWD & FWD TILL FOLLOW INSTRUCTIONS IN OPERATOR’S MANUAL SHIFTING MAY REQUIRE PARTIALLY ENGAGING CLUTCH BAIL FIGURE 3 5 Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING – STOPPING Step 2: Honda Engine -For cold starts, move the TO STOP WHEEL & TINE DRIVE RELEASE WHEEL & TINE CONTROL BAIL FIGURE 4 2.4 ENGINE STARTING PROCEDURE Step 1: Place the WHEEL and TINE SHIFT LEVER in the NEUTRAL position and make sure the WHEEL and TINE CONTROL BAIL is in the released position. Step 2: Briggs Engine -For cold starts, move the CHOKE CONTROL on the engine forward into CHOKE position. See Figure 5. PUSH FORWARD TO CHOKE CHOKE LEVER FIGURE 5 ENGINE KILL SWITCH to the “ON” position. See Figure 5A. Move the CHOKE CONTROL on the engine rearward into CHOKE position. See Figure 5B. MOVE THE ENGINE KILL SWITCH TO “ON” FIGURE 5A MOVE THE CHOKE CONTROL TO THE CHOKE POSITION FIGURE 5B 6 Section 2 - OPERATING INSTRUCTIONS 2.4 ENGINE STARTING PROCEDURE Step 3: Briggs Engine -Move ENGINE SPEED CONTROL to FAST position and turn FUEL VALVE to ON position. See Figure 6. FUEL VALVE MOVE ENGINE SPEED CONTROL TO FAST POSITION FIGURE 6 Step 3: Honda Engine -Move ENGINE SPEED CONTROL to FAST (rabbit) position and move FUEL VALVE forward to ON position. See Figure 6A. ENGINE KILL SWITCH must be in ON position. See Figure 5A. MOVE ENGINE SPEED TO THE FAST POSITION MOVE FUEL VALVE TO ON POSITION FIGURE 6A Step 4: Move to the right side of Tiller and place your foot on top of the right wheel (See starting procedure decal located on top of the tine cover), hold handle bar, then pull the ROPE STARTER HANDLE in smooth, steady motion until the engine starts. To prolong the life of the rope, guide the handle back to the engine rather than allowing it to snap back. Step 5: Briggs Engine -Allow a brief warm-up period, then move the CHOKE CONTROL rearward to RUN POSITION and the ENGINE SPEED CONTROL to the desired speed setting. Refer to the tilling procedure section. Step 5: Honda Engine -Allow a brief warm-up period, then move the CHOKE CONTROL forward to the OFF POSITION. Move the ENGINE SPEED CONTROL to the desired speed setting. Refer to the tilling procedure section. Step 6: Briggs Engine -To STOP the engine, pull the ENGINE SPEED CONTROL on engine rearward into STOP position. Turn FUEL VALVE to OFF position. Step 6: Honda Engine -To STOP the ENGINE move the ENGINE KILL SWITCH to the OFF position. Move FUEL VALVE rearward to OFF position. 2.5 HANDLE BAR ADJUSTMENT Remove retaining screw and nut from handle bar bracket. Adjust handle bar “UP” or “DOWN” as required. Reinstall screw and nut. See Figure 7. LOW MEDIUM REMOVE HIGH SCREW TO...