Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
2 TABLE OF CONTENTS ............................................................................ 3 SECTION 1 FAMILIARIZATION......................................................................... 4 CONTROL IDENTIFICATION & SAFETY SIGN ........................ 5-6 SECTION 2 - OPERATING INSTRUCTIONS......................................... 7-8 Transmission Positions ............................................................... 7 Pre-Start Checklist........................................................................ 7 Starting & Stopping ...................................................................... 7 Handlebar Adjustment.................................................................. 8 Transporting.................................................................................. 8 Tilling Procedure........................................................................... 8 SECTION 3 - ADJUSTMENTS & REPAIR...........................................9-11 Service Parts & Assistance.......................................................... 9 Standing Tiller On End ................................................................. 9 Tiller Lubrication......................................................................9-10 Tiller Tines................................................................................... 10 Belt Adjustment & Replacement...........................................10-11 Off Season Storage..................................................................... 11 Tine Replacement ....................................................................... 11 WARRANTY............................................................................................ 12 PRIMARY MAINTENANCE ................................................................ 13-16 NOTES ............................................................................................... 17-19 3 Section 1 - FAMILIARIZATION HANDLEBAR CLUTCH CABLE COVER WHEEL & TINE CONTROL BAIL WHEEL & TINE SHIFT LEVER SHIFT COVER DASH ENGINE SPEED CONTROL PANEL LEFT SIDE SHOWN TO VIEW CHECK PLUG ENGINE AIR FILTER HANDLE BRACKET CHOKE CONTROL DEPTH BAR MAIN CASE GREASE CHECK PLUG ENGINE TINE DRIVE COVER BELT GUARD DRAG ENGINE OIL SHIELD CHECK/FILL PLUG MAIN CASE OIL DRAIN FILL PLUG PLUG TINE STARTER ROPE WEIGHT BOX TIRE & WHEEL STAND-UP TRANSMISSION CHAIN CASE BAR FIGURE 1 1.1 INTRODUCTION: This manual covers the recommended operating procedure and routine service requirements on SNAPPER Intermediate Rear Tine Tiller. It is recommended that all operators of this Tiller become thoroughly familiar with the controls and proper operation of the unit before operating. Specific details involving the engine are found in the separate engine owner’s manual. Study these manuals before operating and keep both handy for future reference. Refer to Figure 1 above for location of controls and other essential components. 4 CONTROL IDENTIFICATION & SAFETY SIGNS WARNING: Advises operator of safety procedures that should be followed to prevent injury. OPERATING INSTRUCTIONS: Describes operating instructions. 1) Handle position. 2) Depth of tilling. 3) Engine starting procedure. 4) Tiller clutch engagement. STARTING PROCEDURE: Describesprocedure for starting tiller. WARNING: Advises operator of the dangerof the rotating tines. WARNING: Warns operator to read WARNING: Warns of possible fire hazard operator’s manual and observe all labels from leaking fuel. Also warns of potential and safety instructions before operating engine damage from leaking fuel. tiller. EUROPEAN PERFORMANCE: Maximum level of vibration measured at the operators hand is 22.0 m/sec2. 5 CONTROL IDENTIFICATION & SAFETY SIGNS WHEEL & TINE CONTROL BAIL: Both decals describe operation of wheel & tine control. As the wheel & tine control bail is rotated rearward the wheels & tines will start rotating. The wheel & tine control bail is released and rotates forward the wheels & tines will stop but, the engine will continue operating. WHEEL & TINE CONTROL: Describes operational shifting positions . ATTENTION: Describes procedure for engine lubrication check. SERIAL PLATE: Lists model and serial numbers for proper identification and ordering parts. PATENT NUMBERS: Describes current patent numbers being used for Snapper products. YEAR OF MANUFACTURE: Represents EUROPEAN COMMUNITY: Identification decal the year of manufacture of machine. representing the European community. SNAPPER: Manufacturers name of the product. 6 Section 2 - OPERATING INSTRUCTIONS 2.1 BEFORE OPERATING: Be thoroughly familiar with the operation of ALL controls and how to use them BEFORE operating your Tiller. Transmission shifting is done by shifting the WHEEL and TINE SHIFT LEVER into the desired position. See Figure 3. 2.1.1. TRANSMISSION POSITIONS: The tiller has five different transmission positions. They are as viewed from the operator’s position, viewed from the left to right as follows: 1. FWD & FWD TIL -(Forward Rotat...