Stimmen - 3, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
7102356 (Rev. C, 06/04/2008) TP 200-5352-C-AT-N IMPORTANT SAFETY INSTRUCTIONS WARNING All safety instructions and operating instructions in the manuals provided with the Snapper Lawn Tractor and this Grass Catcher attachment must be followed. Read, understand, and follow ALL instructions and warnings in the Operator’s Manual provided with the machine, with this attachment, and ALL instructions and warnings on the machine, engine and attachment. Failure to comply with ALL instructions and warnings can result in damage, serious injury or death to the operator or other persons. 1) DO NOT allow children or others in the yard when the machine is operated (even with the blades off). 2) DO NOT allow children or others to ride on the machine or attachment (even with the blades off). 3) DO NOT allow children to operate the machine. 4) DO NOT operate blades in reverse. STOP blades. LOOK and SEE behind and down for children, pets, and hazards before and while backing. 5) DO NOT operate machine without entire Grass Catcher and Bags installed. 6) DO NOT operate machine on slopes exceeding 10 degrees (18% grade) when equipped with grass catcher. 7) Exercise EXTREME CAUTION on all slopes. Turn blades off when traveling uphill. Use a slow speed and avoid sudden or sharp turns. 8) DO NOT operate machine across face of slopes. Operate up and down. Practice on slopes with blades off. 9) AVOID uphill starts. If machine stops going up hill or tires lose traction, turn blades OFF and back slowly straight down the slope. 10) GRASS CATCHER COMPONENTS are subject to deterioration during normal use. Inspect all components frequently for signs of wear and deterioration. Replace worn or damaged components immediately. 11) DO NOT leave machine with engine running. STOP engine, STOP blades, SET brake, and REMOVE key before leaving operator’s position for any reason. 12) DO NOT attempt to remove or unclog the grass catcher with engine or blades running. Stop engine and blades and make sure all rotating components have come to a complete stop before removing any catcher component or attempting to unclog catcher or deck. 13) DO NOT operate machine with Catcher open. The catcher must be closed at all times, unless dumping grass bags. Stop blades before dumping grass catcher. Instruction Manual No. 7102356 (Rev. C, 06/04/2008) 2 TP 200-5352-C-AT-N Installation Instructions Install Bagger Mount 1) Remove three bolts – two on the rear of the tractor frame, and the top bolt on the right rear of the tractor frame. See Figure 1. The two rear bolts will be replaced with longer bolts supplied in the kit. Save the right bolt for reinstallation. Figure 1 ‘Hitch Mount’ hole Install Grass Bag Support 1) Align the lower U-shaped channel on the Grass Bag Support (7500994) with the U- shaped slot in the top of the Bagger Mount. Insert the channel support fully into the bagger mount. See Figure 2. Figure 2 2) Align the holes in the Bagger Mount Weldment (P/N 7400272A) with the holes in the tractor frame. 3) Install one bolt 1/2-13x1-1/4 (7091323, not shown) into the hole in the lower bagger mount and the tractor frame (‘hitch mount’ hole). See Figure 1. Secure with one hex nut 1/2-13 (7091544). Do not tighten hardware at this time. 4) Install two bolts 5/16-18x1-1/4 (1930595) into the rear of the tractor frame. These replace the two removed in Step 1. Secure with two flange hex nuts 5/16-18 (1927557). Also, re-install the right bolt into the right rear of the tractor frame. 5) Tighten all hardware securely. 2) Secure the Grass Bag Support to the Bagger Mount with the Mounting Pin (M720527). Hold the pin with the leg up. Insert the Mounting pin fully into the Bagger Mount. Rotate the mounting pin so that the leg will be pointing down, locking the pin in place. See Figure 3. Figure 3 Instruction Manual No. 7102356 (Rev. C, 06/04/2008) 3 TP 200-5352-C-AT-N Install Grass Bags 1) Align the slot on the hanger of the Grass Bag Assembly (7500995) with the tab on the grass bag support. 2) Insert the tab into the slot. Repeat for all three grass bags. See Figure 4. Figure 4 Install Cover Assembly 1) Attach the Cover Assembly (7500996) to the Grass Bag Support. Insert one Hinge Pin (M720525) into each hinge, and secure with one Hair Pin (1960074). See Figure 5. 2) Lower the cover, and pull the latch down over the grass bag frame. The cover must be fully closed and latched. Figure 5 Install Grass Bag Adapter 1) 46” & 52” Models Only – Attach the Latch Pin (M720543) to the appropriate Grass Bag Adapter, using one carriage bolt 1/4-20x5/8 (1960252) and one center lock flange nut 1/4-20 (1930642). See Figure 6 (inset). 2) The Grass Bag Adapter attaches to the deck using two bolts and two wing nuts, provided with the kit. See Figure 6. Note – some model tractors will already have the bolts installed in the deck. You can use them to attach the grass bag adapter. Figure 6 Grass Bag Adapter 42” – 7501003 46” – M720560 52” – 7102377 3) Lift the discharge deflector. Align the ...