Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Billy Goat, modell BC2401H

Hersteller: Billy Goat
Dateigröße: 632.21 kb
Dateiname: acaba499-cfc6-4989-9c96-64f3f20da600.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

(See trouble shooting pushing the machine. section on page 12). CLEARING A CLOGGED CUTTING DECK: ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used. PUT OIL IN ENGINE BEFORE STARTING. 16.1 STARTING Turn engine off and wait for blade to stop completely. Disconnect spark plug wire. Wearing durable gloves, remove clog. Danger, the clog may contain sharp materials. Reconnect spark plug wire. BLADE CLUTCH Engine must be level when checking and filling oil and The Brush Cutter blade clutch is controlled by an operator gasoline. presence control. To engage the blade, depress the operator's ENGINE SPEED: Controlled by throttle lever on the handle. left hand control lever against operator's handle. The blade is disengaged by releasing this lever.(See Fig. 1.1) FUEL VALVE: Move fuel valve to "ON" position (when provided on engine). NOTE: The blade clutch must be either fully engaged for cutting CHOKE: Operated by remote throttle on handle. To choke or fully disengaged to bring the blade to a stop. Do not operate engine move the throttle to full fast position. the unit with the blade clutch partially engaged. Premature belt NOTE: HONDA MODELS ONLY: Pull the control lever out wear and clutch failure will result from improper operation of the completely and turn clockwise to lock the control in choke. clutch. After starting the engine, unlock the t-handle by turning CAUTION: Use extreme care when operating the counter clockwise, and push in to set the desired engine blade. Inspect the work area for foriegn objects speed and lock in place. that could cause damage to the unit or injure the operator if struck by the blade. Never operate the THROTTLE: Move remote throttle control to fast position. blade with bystanders in the work area. Pull starting rope to start engine. ELECTRIC START: Choke the engine if necessary. Pull up on the sleeve on the toggle switch, push it up to start position and hold until engine starts, then release switch and it will return to the run position. IF YOUR UNIT FAILS TO START: See Troubleshooting on page 12. Lever Down Engages Clutch Lever Up Disengages Clutch Lever Handle CUTTING OPERATION 16.2 GENERAL OPERATION: To engage the blade, depress the operator's left hand control lever against operator's handle. The blade is disengaged by releasing this lever.(See Fig. 1.1) To engage the wheel drive, lift the operator's right hand control lever against operator's handle. The drive is disengaged by releasing this lever.(See Fig. 1.2) Ground speed can be varied by shifting gears as described on page 9. To begin cutting engage the blade lever, allow the blade to spin up to speed, and engage the wheel drive to begin moving forward into the material to be cut. Fig. 1.1 Part No. 500264 Page 5 of 12 Form No. F071300A Part No. 500264 Page 6 of 12 Form No. F071300A 18 PARTS DRAWING BC2401HE, BC2401H, BC2401 19 19 PARTS LIST ITEM NO. DESCRIPTION BC2401HE Part No QTY BC2401H Part No QTY BC2401 Part No QTY 1 Deck Assembly with labels 500239 1 500239 1 500239 1 2 Deck WA BC2401 500266 1 500266 1 500266 1 3 Deflector Front BC2400 500125 1 500125 1 500125 1 4 Base Assembly with labels 500240 1 500240 1 500240 1 5 Handle Brace Left 500196 1 500196 1 500196 1 6 Handle Brace Right 500200 1 500200 1 500200 1 7 Door Base Engine 500233 1 500233 1 500233 1 8 Transaxle 3 SPD BC2400 500100 1 500100 1 500100 1 9 Pulley 5.0" OD ‘A’ Sec. 830180 1 830180 1 830180 1 10 Belt Traction Drive 500119 1 500119 1 500119 1 11 Plate Pivot Idler / Shifter 500122 1 500122 1 500122 1 12 Shifter Pivot WA 500169 1 500169 1 500169 1 13 Pulley Idler 800260 1 800260 1 800260 1 14 Wheel & Tire 16" AG SP LH 500103 1 500103 1 500103 1 15 Wheel & Tire 16" AG SP RH 500104 1 500104 1 500104 1 16 Arm Idler WA 500170 1 500170 1 500170 1 17 Cable Clutch Blade BC2400 500259 1 500259 1 500259 1 18 Cable Clutch Drive BC2400 500146 1 500146 1 500146 1 19 Bar Shift T-axle 500121 1 500121 1 500121 1 20 Angle Support T-axle 500127 1 500127 1 500127 1 21 Rod Link Shifter 500144 1 500144 1 500144 1 22 Tube Shift With Grip 500171 1 500171 1 500171 1 23 Clutch Brake BC2401 500258 1 500258 1 500258 1 24 Grip 3/4 ID -Black 610102 1 610102 1 610102 1 25 Tube Pointer 500184 1 500184 1 500184 1 26 Plate Mount Idler WA 500228 1 500228 1 500228 1 27 Pulley Idler 4.5" OD X 3/8 500270 1 500270 1 500270 1 28 Shaft Traction Drive 500226 1 500226 1 500226 1 29 Belt Blade Drive 500237 1 500237 1 500237 1 30 Spacer Spindle BC2401 500232 1 500232 1 500232 1 31 Bar Guard WA BC2401 500235 1 500235 1 500235 1 32 Bushing Shifter 500130 1 500130 1 500130 1 33 Spacer Crank BC2401 500260 1 500260 1 500260 1 34 Spindle WA BC2400 500174 1 500174 1 500174 1 35 Bearing 7/8" ID Sealed Press 500101 2 500101 2 500101 2 36 Shaft Drive Blade 500107 1 500107 1 500107 1 37 Spacer Spindle Bearing 500115 1 500115 1 500115 1 38 Pulley 7" OD x 7/8" BORE 500253 1 500253 1 500253 1 39 Lever Control Blade 500312 1 500312 1 500312 1 40 Handle Upper BC2400 500243 1...