Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Know how to operate your tractor before using the broadcast spreader attachment. • Read the chemical label instructions and cautions for handling and applying the chemicals purchased for spreading. • Wear eye and hand protection when handling and when applying lawn or garden chemicals. • Never operate tractor and spreader attachment without wearing substantial footwear, and do not allow anyone to ride or sit on spreader attachment frame. • Never allow children to operate the tractor or spreader attachment, and do not allow adults to operate without proper instructions. • Always begin with the transmission in first (low) gear and with the engine at low speed, and gradually increase speed as conditions permit. Maximum towing speed - 6 M.P.H. • When towing broadcast spreader do not drive too close to a creek or ditch and be alert for holes and other hazards which could cause you to loose control of the broadcast spreader and tractor. • Before operating vehicle on any grade (hill) refer to the safety rules in the vehicle owner's manual concerning safe operation on slopes. Stay off steep slopes! • Follow maintenance and lubrication instructions as outlined in this manual. Look for this symbol to point out important safety precautions. It means — Attention!! Become alert!! Your safety is involved. HARDWARE PACKAGE CONTENTS ACDEFGIJKHB 134 45 6 91056782 REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION A 2 Hex Bolt, 1/4" x 1-1/2" B 4 Hex Bolt, 1/4" x 1-3/4" C 4 Hex Bolt, 1/4" x 2" D 8 Nut, 1/4" E 2 Hair Cotter Pin, 1/8" F 3 Plastic Cap G 2 Washer, 1/4" H 1 Hitch Pin I 2 Hex Flange Bearing J 2 Spacer K 2 Hub Cap CARTON CONTENTS 8. Hitch Brackets (2) 9. Drive WHeel 10. Wheel 4. Impeller Assembly 5. Hitch Tube, R.H. (Right Hand) 6. Hitch Tube, L.H. (Left Hand) 7. Hitch Control Tube 1. Hopper 2. Control Cable 3. Frame Tube ASSEMBLY • Slide a spacer (J) over the right side of the axle. See figure 3. • Attach the drive wheel (9) to the right (indented) side of the axle. Secure the wheel in place with a hub cap (K). See figure 3. TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches • Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify using the illustrations on page 3. • Insert each side of the axle of the impeller assembly into the frame tube. See figure 1. • Insert the two hex flange bearings (I) into the frame tube. See figure 1. KMJ II 9 FIGURE 3 • Slide a spacer (J) over the left side of the axle. See figure 4. • Attach the wheel (10) to the left side of the axle. Secure the wheel in place with a hub cap (K). See figure 4. FIGURE 1 • Attach the hopper to the frame tube using two 1/4" x 1-1/2" hex bolts (A), 1/4" washers (G), and 1/4" nylock nuts (D) as shown in figure 2. Tighten. • Insert an 1/8" hair cotter pin (E) into the hole at the top of the impeller. See figure 2. KNJ DDAAHHE 10 FIGURE 4 FIGURE 2 • Assemble the Control Cable to the Hitch Control Tube using the carriage bolt and nylon wing nut. Tighten. See figure 7. • Assemble the (RH) and (LH) hitch tubes to the control tube using two 1/4" x 1-3/4" hex bolts (B) and 1/4" nylock nuts (D). Tighten. See figure 5. • Assemble the plastic caps onto the ends of the hitch tubes and control tube as shown in figure 5. BDFFF FIGURE 5 FIGURE 7 • Assemble the Hitch Brackets to the Hitch Control Tube using two 1/4" x 1-3/4" hex bolts (B) and 1/4" nuts (D). Tighten. See figure 8. • Assemble the hitch pin (H) through the hitch brackets and secure with the 1/8" hair cotter pin (E). See figure 8. • Attach the (RH) and (LH) hitch tubes to the frame tube using four 1/4" x 2" hexbolts (C) and 1/4" nylock nuts (D). Tighten. See figure 6. BD HE CD D FIGURE 6 FIGURE 8 OPERATION KNOW YOUR SPREADER Read this owner's manual and safety rules before operating your Spreader. Compare the illustration below with your Spreader to familiarize yourself with the various controls and their locations. USING YOUR SPREADER • Check the material package and the Spreader Settings sheet included with your spreader for the proper spreader setting and application rate. • Before filling spreader, move the control lever to the "OFF" position. • Move spreader onto a flat surface - either a walk or a driveway - and fill. • Slide the Adjustable Stop to the desired setting. • Start the spreader in motion, then move the control lever forward against the adjustable stop to begin spreading. NOTE: Always place control lever in the "OFF" position while filling spreader and when stopping or turning, to prevent release of excess fertilizer. FLOW CONTROL LEVERADJUSTABLE STOP APPLICATION TIPS • This unit will cover a 4 to 8 foot wide area depending on the material used and the towing speed. • To avoid misses or striping, make each pass about 5 feet from the previous one so some overlapping of spread pattern does occur. • For easiest application, spread across the shortest edges of lawn first, making two "header" strips for a turning area, and then spreading between the header strips...