Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
If a spark arrester is used, it should be maintained in effective working order by the operator. In the state of California, the above law is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on Federal lands. A spark arrester for the muffler is available through your nearest Sears Authorized Service Center. ASSEMBLY TO REMOVE UNIT FROM CARTON • Cut from top to bottom all four corners of the carton and lay panels flat. (See Fig. 1) • Remove the lag screw that holds the floating hitch to the packing skid. • Disassemble and discard carton's wood top and side supports. • Remove four hex bolt, hex nuts and flat washer from the hold down brackets at the rear of the carton. • Remove and save the two Flat Washers and Cotter Pins from the rear axle. Reuse when attaching gauge wheels. • Discard all other packing hardware and hold down brackets. TO INSTALL THE TILLER GAUGE WHEELS • Assemble Gauge Wheels onto the Rear Axle with the extended end of Hub facing inward. Secure with the Flat Washers and Cotter Pins which you removed from the axle during unpacking. (See fig. 2.) FIG. 2 TO INSTALL THE TILLER TINE ASSEMBLIES • Attach the floating hitch to the tractor's draw bar. (Refer to Operating Instructions on page 7.) • Remove the preassembled 3/8" x 2" hex bolt and 3/8" nylock nut from the L.H. Tine Assembly. Slide the tine assembly onto the Transmission Axle on the left side of the tiller and secure with the hex bolt and nylock nut. (See fig. 3.) Repeat for the R.H. side. 3/8" NYLOCKNUT FIG. 1 • Right hand (RH) and left hand (LH) are determined from the drivers position while seated on the tractor. • We recommend that you remove the Mower Deck before using the Tiller. Refer to your Tractor Owner's Manual. FIG. 3 TO INSTALL (WHEEL) WEIGHTS TO TILLER NOTE: Weights are not furnished with the Tiller. 30 lb. tractor wheel weights may be purchased to mount to the Tiller if extra weight is required. (Refer to the Operation section of this manual.) • Remove two Carriage Bolts and Nuts from each Tine Shield, located approximately 3-1/2" from the front edge. See fig. 4. • Place (Wheel) Weights on Tine Shield and secure with long Bolts and Nuts furnished with the Weights. See fig. 4. FIG. 4 OPERATION FIG. 5 SAFETY SWITCH - prevents engine from starting while tine clutch lever is engaged LIFT HANDLE - selects tilling or transport position by moving gage wheels TINE CLUTCH LEVER - starts and stops tine rotation FLOATING HITCH - telescoping hitch limits shock loads to tractor RECOIL START HANDLE - used to start the engine THROTTLE CONTROL - controls engine speed FUEL SHUT OFF - shuts of fuel to engine CHOKE CONTROL - used when starting a cold engine DEPTH STAKE - controls tilling/cultivating depth The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over the spectacles or standard safety glasses. HOW TO USE YOUR TILLER BEFORE STARTING YOUR TILLER FILL THE ENGINE WITH OIL! Your tiller engine is shipped without oil or gasoline. Add oil and gas as instructed in the separate engine manual. ATTACHING TILLER TO TRACTOR (See Fig. 6) • Rear wheel weights and tire chains can be used on tractor if additional traction is required for tilling. • Place Tiller on ground level and back up tractor to it. • Slide Floating Hitch of Tiller onto the tractor drawbar so that the hitch pin holes line up. • Insert hitch pin until it extends through bottom of Floating Hitch. Insert hair cotter pin into hitch pin. WARNING: Never fill fuel tank indoors, or with the engine running, or while the engine is hot. Do not smoke while filling tank. STOPPING YOUR TILLER TINES • Raise tiller to transport position. • Pull forward on tine clutch lever. ENGINE (Refer to separate engine manual.) • Move throttle control to "STOP" position. • Turn shut off to "OFF" position. • Never use choke to stop engine. STARTING YOUR TILLER (Refer to separate engine manual.) CAUTION: The muffler and adjacent areas are hot! • Check oil and gas in Tiller engine. • Attach spark plug wire to spark plug. • Pull forward on tine clutch lever to disengage tines. A safety switch prevents engine from starting while tines are engaged. • Turn shut off to "ON" position. • Move choke lever on engine to CHOKE position. (A warm engine may not require choking.) • Move throttle control lever on engine to FAST position. • Grasp starter handle and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Let the rope rewind slowly. • Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Let rope rewind slowly. Do not let starter handle snap back against starter. • Repeat instructions in two preceding paragraphs until engine fires. When engine s...