Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
HOW TO USE YOUR TILLER Know how to operate all controls before adding fuel and oil or attempting to start engine_ STOPPING TINES • Release tine control to stop movement. ENGINE o Move throttle control to "STOP" position. o Never use choke to stop engine. "Sne Control "ON" /" Forward Tine Control (DOWN) Position _ / ""OFF (UP) Position / Throttle Control TINE OPERATION FORWARD ° Squeeze forward tine control to handle. TILLING The speed and depth of tilling is regulated by the position of the depth stake and wheel height. The depth stake should always be below the wheels for digging. It serves as a brake to slow the tiller's forward motion to enable the tines to penetrate the ground. Also, the more the depth stake is lowered into the ground the deeper the tines will dig. DEPTH STAKE Adjust depth stake by removing the hair_ pin clip and clevis pin. Change depth stake to desired position° Replace the clevis pin and hairpin clip= o For normal tilling, set depth stake at the second or third hole from the top, WHEELS Adjust wheels by removing the hairpin clip and clovis pin, Change wheel position. Replace the hairpin clip and clevis pin_ . For normal tilling, set wheels at the sec ond or third hole from the top_ _C 'A'' Depth Stake lip end Clevis Pin Wheel TRANSPORTING YOUR TILLER _,CAUTION: Before lifting or transporting, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gaso line from fuel tank. AROUND THE YARD = Tip depth stake forward until it is held by the stake spring. o Push tiller handles dow._, raising tines off the ground. o Push or pull tiller to desired location. AROUND TOWN o Disconnect spark plug wire. o Drain fuel tank_ = Transport in upright position to prevent oil leakage. BEFORE STARTING ENGINE IMPORTANT: Be very careful not to allow dirt to enter the engine when checking or adding oil or fuel. Use clean oil and fuel and store in approved, clean, covered containers, use clean fill funnels. FILL ENGINE WITH OIL o Remove hangtag from engine= o With engine level, remove engine oil filler plug. o Fill engine with oil to point of overflowing. For approximate capacity see "PRODUCT SPECIFICATIONS on page 4 of this manual= 8 " Tilttillerbackonitswhe_lsandthenrelevel o Withenginelevel,refilltopointofoverflowingif necessary.Replaceoilfiller plug. o Forcoldweatheroperationyoushould changeoil for easierstarting(See "OIL VISCOSITYCHART intheCustomer Responsibilitiessectionof thismanual). o Tochangeengineoil,seetheCustomerResponsibilitiessectionof thismanual° OilLevel. Filler Plug ADD GASOLINE = Fill fuel tank. Use fresh, clean, regular unleaded gasoline. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life.) IMPORTANT: When operating in Temperatures below 32°F (0°C), use fresh, clean, winter grade gasoline to help insure good cold weather starting_ WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty Use fresh fuel next season. See Storage section of this manual for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur ,_CAUTION: Fil! to within t/2 inch of top of fuel tank to prevent spills and to allow for fuel expansion. If gasoline is accidentally spilled, move machine away from area of spill, Avoid creating any source of ignition until gasoline vapors have disappeared. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. _ START ENGINE CAUTION: Keep tine control in "OFF" position when starting engine° When starting engine for the first time or if engine has run out of fuel, it will take extra pulls of the recoil starter to move fuel from the tank to the engine. o Make sure spark plug wire is properly connecte& • Place throttle control in "FAST' position. • Move choke control to full "CHOKE" position, Grasp recoil starter handle with one hand and grasp tiller handle with other hand Pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). o Pull recoil starter handle quickly. Do not let starter handle snap back against starter. Repeat if necessary. • If engine fires but does net start, move choke control to half choke position. Pull recoil starter handle until engine starts. ° When engine starts, slowly move choke control to "RUN" position as engine warms up. NOTE: A warm engine requires less choking to start. o Move throttle control to desired running position. o Allow engine to warm up for a few minutes before engaging tine& NOTE: If at a high altitude (3000 feet) or in cold...