Stimmen - 3, Durchschnittliche Bewertung: 3 ( )

Hersteller: Ryobi Dateigröße: 2.87 mb Dateiname: Unterrichtssprache:

1 Liter 20 cc (20 ml) FILLING TANK . C l e a n s u r f a c e a ro u n d f u e l c a p t o p re v e n t contamination. . Loosen fuel cap slowly. Rest the cap on a clean surface. . Clean and inspect the gasket. . Carefully pour fuel into the tank. Avoid spillage. . Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage. NOTE: It is normal for smoke to be emitted from a new engine after first use. WARNING: Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting engine. Do not smoke! OPERATING THE TRIMMER See Figure 15. WARNING: Always position the unit on the operator’s right side. The use of the unit on the operator’s left side will expose the user to hot surfaces and can result in possible burn injury. WARNING: To avoid burns from hot surfaces, never operate unit with the bottom of the engine above waist level. Hold the trimmer with your right hand on the rear handle and your left hand on the front handle. Keep a firm grip with both hands while in operation. Trimmer should be held at a comfortable position with the rear handle about hip height. Always operate trimmer at full throttle. Cut tall grass from the top down. This will prevent grass from wrapping around the shaft housing and string head which could cause damage from overheating. If grass becomes wrapped around the string head, STOP THE ENGINE, disconnect the spark plug wire, and remove the grass. Prolonged cutting at partial throttle will result in oil dripping from the muffler. OPERATION Fig. 15 PROPER OPERATING POSITION 16 WARNING: Always hold the string trimmer away from the body keeping clearance between the body and the product. Any contact with the housing or string trimmer cutting head can result in burns and/or other serious personal injury. TO ADVANCE THE CUTTING LINE String advance is controlled by tapping the string head on grass while running engine at full throttle. . Run engine at full throttle. . Tap the spool retainer on ground to advance string. The string advances each time the spool retainer is tapped. Do not hold the spool retainer on the ground. NOTE: The line trimming cut-off blade on the grass deflector will cut the line to the correct length. NOTE: If the string is worn too short you may not be able to advance the string by tapping it on the ground. If so, stop the engine, and manually advance the string. TO ADVANCE THE CUTTING LINE MANUALLY With the engine off, push the spool retainer down while pulling on string(s) to manually advance the string. CUTTING TIPS See Figures 15 - 17. . Avoid hot surfaces by always keeping the product away from your body. (Proper operating position shown in figure 15.) . Keep the trimmer tilted toward the area being cut; this is the best cutting area. . The curved shaft trimmer cuts when passing the unit from right to left. The straight shaft trimmer cuts when passing the unit from left to right. This will avoid throwing debris at the operator. Avoid cutting in the dangerous area shown in illustration. . Use the tip of string to do the cutting; do not force string head into uncut grass. . Wire and picket fences cause extra string wear, even breakage. Stone and brick walls, curbs, and wood may wear string rapidly. . Avoid trees and shrubs. Tree bark, wood moldings, siding, and fence posts can easily be damaged by the string. GRASS DEFLECTOR LINE TRIMMING CUT-OFF BLADE See Figure 18. The trimmer is equipped with a line trimming cut-off blade on the grass deflector. For best cutting, advance string by tapping the string head until the string is trimmed to length by the cut-off blade. Advance the string whenever you hear the engine running faster than normal, or when trimming efficiency diminishes. This will maintain best performance and keep the string long enough to advance properly. BEST CUTTING AREA DANGEROUS CUTTING AREA Fig. 17 DIRECTION OF ROTATION DANGEROUS CUTTING AREA Fig. 16 BEST CUTTING AREA Fig. 18 STRAIGHT SHAFT TRIMMER LINE TRIMMING CUT-OFF BLADE CURVED SHAFT TRIMMER LINE TRIMMING CUT-OFF BLADE DIRECTION OF ROTATION STRAIGHT SHAFT TRIMMER CURVED SHAFT TRIMMER OPERATION 17 . Inspect and clear the area of any hidden objects such as glass, rocks, concrete, fencing, wire, wood, metal, etc. . Never use blades near sidewalks, fencing, posts, buildings or other immovable objects. . Never use a blade after hitting a hard object without first inspecting it for damage. Do not use if any damage is detected. . The unit is used as a scythe, cutting from the right to the left in a broad sweeping action from side to side. . Use only the Tri-Arc® blade. To install any other brand blade or cutting head to this brushcutter can result in serious personal injury. WARNING: To avoid burns from hot surfaces, never operate unit with the bottom of the engine above waist level. OPERATING THE BRUSHCUTTER See Figures 19 - 20. Hold the brushcutter with your right hand on the rear handle and your lef...

Herunterladen

Geben Sie zwei Ziffern: