Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Ryobi Dateigröße: 6.34 mb Dateiname: Unterrichtssprache:

• Insert the end of the J-handle between the clamps so that holes align and handle will be located to the operator’s left. • Push the bolt through the clamp and handle. • Install flat washer, lock washer, and wing nut to hold the assembly in place. • Adjust the position of the handle to the area indicated by the label on the drive shaft housing. • Tighten the wing nut securely. ATTAChINg ThE gRASS DEFLECTOR WARNINg: The line cutting blade on the grass deflector is sharp. Avoid contact with the blade. Failure to avoid contact can result in serious personal injury. TO ATTACh ThE CURVED ShAFT gRASS DEFLECTOR - CS26 See Figure 6. • Remove hex screw, flat washer, and wing nut from grass deflector. • Press the grass deflector onto the bottom of the curved shaft as shown. • Insert the hex screw through the grass deflector and the bracket on the curved shaft. • Place the flat washer on the hex screw. • Place the wing nut on the hex screw and tighten securely. TO ATTACh ThE STRAIghT ShAFT gRASS DEFLECTOR - SS26 See Figure 7. • Remove the wing screw from the grass deflector. • Insert the tab on the mounting bracket in the slot on the grass deflector. • Align the screw hole in the mounting bracket with the screw hole in the grass deflector. • Insert the wing screw through the mounting bracket and into the grass deflector. • Tighten the screw securely. ATTAChINg ThE bRUShCUTTER gUARD - bC26 See Figure 8. The guard is shipped installed on these brushcutter models. Instructions have been included for reference when changing from string trimmer operation back to brushcutter operation. • Withthestringheadremoved,placethebrushcutterguard on the gear head as shown. • Install the three hex head screws from bottom through the guard and into the gear head. • Tighten the screws securely and torque to 40-50 in.lb. minimum. ATTAChINg ThE ShOULDER hARNESS - bC26 See Figure 9. • Connect the latch on the shoulder harness to the strap hanger. • Adjust the strap to a comfortable position. CONVERTINg FROM bRUShCUTTER TO STRINg TRIMMER - bC26 To convert from the brushcutter to the string trimmer, remove the blade and brushcutter guard, attach the straight shaft grass deflector and install the string head. 8 — English ASSEMbLY ASSEMbLY REMOVINg ThE TRI-ARC® bLADE AND bRUShCUTTER gUARD See Figures 10 - 11. • Align the slot in the flanged washer with the slot in the gear head. • Place the gear head locking tool through the slot in the flanged washer and gear head. • Remove the blade nut by turning it clockwise. • Remove the cupped washer and the blade. • Remove the flanged washer from the gear head shaft and retain it for the string head installation. • Remove the three screws securing the brushcutter guard to gear head. • Remove the brushcutter guard. NOTE: Store the brushcutter parts together for later use. INSTALLINg ThE STRAIghT ShAFT gRASS DEFLECTOR AND STRINg hEAD See Figures 10 - 12. • Install the grass deflector. Refer to To Attach the Straight Shaft grass Deflector - SS26 earlier in this manual. • Place the flanged washer on the gear head shaft. NOTE: The hollow side of the flanged washer should face the gear head. • Install the arbor. • Install the string head assembly onto the gear head shaft. Refer to Installing bump Feed String head or Installing Dual Spool™ Fixed Line String head Insert later in this manual. CONVERTINg FROM STRINg TRIMMER TO bRUShCUTTER - bC26 To convert from the string trimmer to the brushcutter, remove the string head assembly and straight shaft grass deflector, attach the brushcutter guard and install the blade. REMOVINg ThE STRAIghT ShAFT gRASS DEFLECTOR AND STRINg hEAD See Figures 10 - 13. • Align the slot in the flanged washer with the slot in the gear head. • Remove the hex head bolt and string head assembly. • Remove the arbor. • Remove the flanged washer and retain it for the blade installation. • Remove the wing screw securing the grass deflector. • Remove the grass deflector. NOTE: Store the string head parts together for later use. INSTALLINg ThE TRI-ARC® bLADE AND bRUShCUTTER gUARD See Figures 10 - 14. • Install the brushcutter guard. Refer to Attaching the brushcutter guard - bC26 earlier in this manual. • Place the flanged washer over the gear head shaft with the hollow side toward the brushcutter guard. • Center the blade on the flanged washer, making sure the blade fits flat and the raised hub of the flanged washer goes through the hole in the blade. • Install the cupped washer with the raised center away from the blade. • Place the blade nut onto the gear head shaft. • Place the gear head locking tool through the slot in the flanged washer and gear head. • Install the blade nut by turning it counterclockwise (left handed threads). • Tighten the blade nut securely and torque to 120 in.lb. minimum. 9 — English OPERATION OPERATION WARNINg: Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNIN...

Herunterladen

Geben Sie zwei Ziffern: