Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Dolmar Dateigröße: 1.32 mb Dateiname: Unterrichtssprache:

Cutting Tools Use only the correct cutting tool. • Resting • Transport • Refuelling • Maintenance • Tool Replacement Caution: Kickback Diagrammatic figure Diagrammatic figure Maintenance instructions -The condition of the Brush Cutter/String Trimmer must be checked before operation, in particular of the cutting tool, the protective devices and also the shoulder strap. Special attention must be paid to the cutting blade which must be correctly sharpened. -Stop the engine and remove spark plug connector when replacing or sharpening cutting tools, and also when cleaning the machine or cutting tool. -Operate the Brush Cutter/String Trimmer with as little noise and contamination as possible. In particular check the correct setting of carburetor. -Clean the Brush Cutter/String Trimmer regularly and ensure that all screws and nuts are well tightened. -Never service or store the Brush Cutter/String Trimmer in the vicinity of naked flames. -Always store the Brush Cutter /String Trimmer in locked rooms and with a emptied fuel tank. -Do not perform any modifications on the Brush Cutter/String Trimmer as this will endanger your safety. -The performance of maintenance or repair work by the user is limited to those activities as described in this instruction manual. All other works are to be done by an Authorized Service Agent. Use only genuine spare parts and accessories supplied by DOLMAR. Use of non-approved accessories and tools means increased risk of accidents. DOLMAR will not accept any liability for accidents or damage caused by the use of non-approved cutting tools and fixing devices of cutting tools, or accessories. First Aid Make sure that a first-aid box is available in the vicinity of the cutting operations in case of accident. TECHNICAL DATA MODEL MS-230 C/231 C MS-260 C/261 C MS-260 U/261 U MS-330 C/331 C MS-330 U/331 U Dry Weight 5.7 kg 5.7 kg 6.5 kg 6.5 kg 7.3 kg Engine TLE23FD-TBM/TBD TLE26FD-TBM/TBD TLE33FD-TBM/TBD Bore x Stroke 31 x 30 mm 33 x 30 mm 36 x 32 mm Displacement 22.6 cm3 25.6 cm3 32.6 cm3 Maximum output 0.7 kW (0.94 HP)/ 8000 rpm 0.8 kW (1.07HP)/8000 rpm 0.97 kW (1.3 HP)/7500 rpm Fuel Mixture of gasoline and lubricanting oil (ratio 50:1) Lubricating oil Two-stroke motor oil FC Fuel Tank Capacity 0.6 lit. 0.8 lit. Spark Plug NGK BPMR8Y Carburetor Diaphragm type (with 2 passage for air and mixture) Main Pipe Drive Shaft Flex/Rigid Rigid Diameter 7 mm Hollow (5 mm) Upper end Involute Spline (7 x 7 x 0.75) Lower end Tube Type Straight Diameter 25.4 mm Wall thickness 1.5 mm Length 1500 mm Finish Silver Anodized Bearings Type Bronze bush in rubber String Head Type Tap and Go N/A Tap and Go N/A O.Dia. 105 mm 105 mm Line size 2.4 mm 2.4 mm Gear Case Assy Arbor size M10LH FEM Gear ratio 14/19 17/21 Clutch Case Assy Anti-Vib Yes Number Brgs 2 Drum dia. 54 mm 78 mm Throttle Control Overmolded Yes First Idle Yes Hanger Type Fixed Guard Type Grass Weed Blade Grass Weed Blade Swath dia 41 cm (16 in.) 43 cm (17 in.) N/A 43 cm (17 in.) N/A Handle Assy Type Loop Bike Loop Bike Barrier N/A Overmolded Yes (Black) N/A Yes (Black) N/A Band Shoulder Type Single Double Tool Set Yes Blade Size N/A 23 cm (9 in.) N/A 23 cm (9 in.) Type Quard Quard Blade Holder N/A Yes N/A Yes 7 MOUNTING OF HANDLE CAUTION: Before doing any work on the Brush Cutter/String Trimmer, always stop the engine and pull the spark plug connector off the spark plug. Always wear protective gloves. CAUTION: Start the engine of Brush Cutter/String Trimmer after making sure that it is assembled completely. STOP For machines with U Handle models -Place the handle-fixing metal so that the handle with the control lever will be positioned on the right (the right-hand grip side) as viewed from the engine side, and the other handle on the left side. -Fit the groove of the handle-fixing material to the handle end. Fix the attached metal by hexagon socket bolts supplied. -Adjust the position of handle for easy and comfortable operation, and then tighten securely the four (4) hexagon socket bolts uniformly on the right and left with the wrench provided. For machines with Loop Handle -Fix a barrier to the left side of the machine together with the handle of operator’s protection. -Do not adjust position of the loop handle too close to the control grip. -The handle must be kept in position more than 250 mm from the hanger. MOUNTING OF PROTECTOR To meet the applicable safety provisions, only the tool/protector combinations as described in the table must be used. Use genuine DOLMAR cu...

Herunterladen

Geben Sie zwei Ziffern: