Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Bolens Dateigröße: 2.18 mb Dateiname: Unterrichtssprache:

8. Clogged fuel tank. 9. Spark plug wire loose. 10. Dirty engine air screen. 11. Dirty/clogged muffler. 12. Carburetor out of adjustment. 13. Poor compression. 1. Set depth stake for shallower tilling. 2. Clean or replace air cleaner cartridge. 3. Check oil level/change oil. 4. Clean and regap or change spark plug. 5. Empty and clean fuel tank and refill, and clean carburetor. 6. Empty fuel tank and refill fuel tank with fresh gasoline. 7. Empty fuel tank and carburetor, and refill tank with fresh gasoline. 8. Remove fuel tank and clean. 9. Connect and tighten spark plug wire. 10. Clean engine air screen. 11. Clean/replace muffler. 12. Make necessary adjustments. 13. Contact an authorized service centerdepartment. Engine overheats 1. Low oil level/dirty oil. 2. Dirty engine air screen. 3. Dirty engine. 4. Partially plugged muffler. 5. Improper carburetor adjustment. 1. Check oil level/change oil. 2. Clean engine air screen. 3. Clean cylinder fins, air screen, and muffler area. 4. Remove and clean muffler. 5. Adjust carburetor to richer position. Excessive bounce/ difficult handling 1. Ground too dry and hard. 1. Moisten ground or wait for more favorable soil conditions. Soil balls up or clumps 1. Ground too wet. 1. Wait for more favorable soil conditions. Engine runs but tiller won’t move 1. Tine control are not engaged. 2. V-belt not correctly adjusted. 3. V-belt is off pulley(s). 1. Engage drive control. 2. Inspect/adjust V-belt. 3. Inspect V-belt. Engine runs but labors when tilling 1. Tilling too deep. 2. Throttle control not properly adjusted. 3. Carburetor out of adjustment. 1. Set depth stake for shallower tilling. 2. Check throttle control setting. 3. Make necessary adjustments. Tines will not rotate 1. Shear pin(s) broken. 1. Replace shear pin(s). Tines skip over ground 1. Drag Stake not lowered in forward rotating till mode. 2. Improper tilling mode. 1. Lower Drag Stake 2. Forward rotating tine drive should only be used for soft ground or for soil that has already been tilled. Hard to shift into gear 1. Gears not timed. 1. Briefly engage tine control and release or rock tiller forward and back ward until are able to shift gears. Tiller shuts off when tine control engaged 1. Shift lever set in between counter rotating till position and forward rotating till position. 2. Tines jammed. 1. Shift to either counter rotating till position or forward rotating till position. 2. Clear tines. 17 18 2 100 101 102 19 31 17 16 11 15 21 27 18 20 11 10 12 6 14 13 42 handle_assy_101 REAR TINE TILLER - MODEL NUMBER 90102800 (MFG. ID. NO. 96096000100) HANDLE ASSEMBLY REAR TINE TILLER - MODEL NUMBER 90102800 (MFG. ID. NO. 96096000100) HANDLE ASSEMBLY ITEM MFG. ARIENS NO. NO. PART NO. DESCRIPTION 2 165787 21546171 Grip, Handle 6 425577 21546735 Console Control 10 8206H 21546825 Handle, Grip 11 4497H 21546739 Retainer Spring 12 81328 21546824 Bolt, Shoulder 13 187497 21546247 Handle, Shift 14 109313X 21546044 Grommet, Rubber 15 138400 21546092 Rod, Shift 16 72110608 21546764 Bolt 3/8-16 x 1 Gr. 5 17 109229X 21546042 Lock, Handle 18 73680600 21546785 Nut, Hex, Crownlock 3/8-16 19 19131611 21546285 Washer 13/32 x ...

Herunterladen

Geben Sie zwei Ziffern: