Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: RedMax Dateigröße: 581.6 kb Dateiname: Unterrichtssprache:

Avoid using brushcutter late at night and/or early in the morning. [6 ] A Safety Precautions ■ Things to be careful about when using your brushcutter •When using your brushcutter, grip the handles of the brushcutter firmly with both hands, place your feet slightly apart (slightly further apart than the width of your shoulders) so that your weight is distributed evenly across both legs, and always be sure to maintain a steady, even posture while working. • Maintain the speed of the engine at the level required to perform cutting work, and never raise the speed of the engine above the level necessary. •Always be sure never to allow other persons to come within the work area while cutting. •Be especially careful not to slip if it is raining or if rain has just stopped, as the ground is likely to be slippery at such times. • If the grass or other object gets caught in the blade during operation, always be sure to turn off the engine before removing the object. •Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Establish a safe method for gaining your attention during operation. Be careful if you are approached. • If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. •Keep operation area clear of all persons, particularly small children and pets. Injury may result from flying debris. •Never touch the spark plug or plug cord while the engine is in operation. Doing so may result in being subjected to an electrical shock. •Never touch the muffler, spark plug, or other metallic parts of the engine while the engine is in operation or immediately after shutting down the engine. These metallic parts reach high temperatures during operation and doing so could result in serious burns. • When you finish cutting in one location and wish to continue work in another spot, turn off the engine, place the protective cover over the blades, and turn the brushcutter so that the blade face away from your body before carrying it to the new location. • Never transport the brushcutter over rough roads over long distances without removing all fuel from the fuel tank. If doing so, fuel might leak from the tank during transport. [7 ] A Safety Precautions ■ Notes on care and maintenance of your brushcutter • In order to maintain your brushcutter in proper working order, perform the maintenance and checking operations described in this manual at regular intervals. In the event that any parts must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance. •Under no circumstances should you ever take apart the brushcutter or alter it in any way. Doing so might result in the brushcutter becoming damaged during operation or the brushcutter becoming unable to operate properly. •Always be sure to turn off the engine before performing any maintenance or checking procedures. •When sharpening, removing, or reattaching the blade, be sure to wear thick, sturdy gloves and use only proper tools and equipment to prevent injury. • When replacing blade or any other parts or when replacing the oil or any lubricants, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax brushcutter. • Do not use any accessory or attachment other than those bearing the RedMax mark and recommended for the unit. [8 ] Set up ■ MOUNTING ENGINE (BC2300DL & BC2600DL) 1. Remove the clamp temporarily attached to the clutch housing. 2. Push the driveshaft toward the gearcase and rotate it by hand to check that the driveshaft is engaged with the gears. 3. Insert the shaft tube into the clutch housing until it bottoms. When difficult to engage, twist the engine slightly. 4. Align the positioning holes on the clutch housing and the shaft tube and fit the boss on the clamp into the holes. Fasten the clamp securely. (BC3400DL & BC4400DW) •Put the engine onto the clutch side end of the driveshaft assembly, making the fuel tank and the cutter head come to the same side. Attach the engine firmly with the 4 screw provided. ■ INSTALLING HANDLE •Mount the handle to the shaft tube and clamp it at your best operating position. B C2300D L/B C2600D L/B C3400D L (BC3400DL) ■ INSTALLING DEBRIS GUARD • Put the debris guard on the shaft tube near the gear box, attach it with the 2 screws and hardware provided. ■ CONNECTING THROTTLE WIRE 1. Remove the air cleaner cover. 2. Connect the end of the throttle wire to the joint on the top of the carburetor. | NOTE | (BC3400DL & BC4400DW) •When installing the cleaner cover, make sure to put the high-tension wire in it. [9 ] Set up ■ CONNECTING SWITCH WIRES •Connect the switch wires between the engine and the main unit. Pair the wires of the same color. ■ PUTTING ON WAIST PAD (BC4400DW ...

Herunterladen

Geben Sie zwei Ziffern: