Stimmen - 6, Durchschnittliche Bewertung: 4.2
(
)
)
|
Anleitung Zusammenfassung
: Pull the thrust washer ( 5) off the shaft ( 2). 1) Comes standard with the machine or is available as special accessory FS 120, FS 200, FS 250 English The rider plate ( 4) is in the parts kit supplied with the machine. : Go to "Mounting the Mowing Head" or "Mounting Metal Cutting Tools". Blocking the Output Shaft 1 002BA081 KN 3 1 2 4 681BA026 KN 5 7 8 2 002BA166 KN7 : Insert the stop pin1) or screwdriver1) ( 7) in the hole ( 8) in the gearhead as far as stop – apply slight pressure. : Rotate nut or cutting tool on the shaft ( 2) until the stop pin slips into position and blocks the shaft. Mounting the Mowing Head Keep instruction sheet for mowing head in a safe place. : : : Screw STIHL SuperCut 20-2, STIHL AutoCut 25-2, 30-2, STIHL TrimCut 30-2 or STIHL PolyCut 20- 3 counterclockwise onto the shaft (1) as far as stop. Block the output shaft. Tighten down the mowing head firmly. Remove the tool used to block the shaft. STIHL FixCut 25- 2 : : : : Place the mowing head on the thrust plate ( 2) Collar ( arrow) must locate in the mowing head’s mounting hole. die Push the thrust washer ( 3) over the shaft ( 1) so that it locates against the base. Block the output shaft. Use the combination wrench ( 5) to screw the mounting nut ( 4) onto the shaft and tighten it down firmly. Remove the tool used to block the shaft. 1) Comes standard with the machine or is available as special accessory FS 120, FS 200, FS 250 English Removing the Mowing Head : Block the output shaft. STIHL SuperCut 20-2, STIHL AutoCut 25-2, 30-2, STIHL TrimCut 30-2, STIHL PolyCut 20-3 : Unscrew the mowing head clockwise. STIHL FixCut 25-2 : Use the combination wrench to loosen and unscrew the mounting nut clockwise from the output shaft. If the mounting nut is too loose, fit a new one. Adjusting Nylon Line STIHL SuperCut Fresh line is advanced automatically if remaining line is still at least 6 cm long. The blade on the deflector trims overlong lines to the correct length. STIHL AutoCut : Hold the rotating cutting head horizontal to the ground – tap it on the ground – about 3 cm fresh line is advanced. The blade on the deflector trims overlong lines to the correct length. Avoid tapping the head more than once. Line feed operates only if both lines still have a minimum length of 2.5 cm. All other mowing heads Refer to instructions supplied with the mowing head. To reduce the risk of serious injury, always shut off the engine before adjusting the mowing line by hand. Replacing Nylon Line or Cutting Blades Refer to instructions supplied with the mowing head. 12 34 56 Mounting metal cutting tools The skirt and line limiting blade are not required for grass cutting blades 230-2 ( 1), 230-4 ( 3), 230-8 ( 2) or the brush knife ( 4) – see " Mounting the Deflector". Fit the appropriate limit stop for circular saw blades 200 ( 5, 6) – see " Mounting the Deflector". 681BA027 KN FS 120, FS 200, FS 250 English Fuel : Lay your brushcutter on its back with the cutting tool mounting face pointing up: Cutting edges of ( 1), ( 3) and ( 4) may point in either direction. Cutting edges of ( 2), ( 5) and ( 6) must point clockwise. Direction of rotation is marked by arrow on inside of cutting head deflector or limit stop. : Place the cutting tool ( 7) on the thrust plate ( 8). Collar (see arrows) must locate in cutting tool’s mounting hole. : Slip thrust washer (9) and rider plate ( 10) over the output shaft ( 11). : Block the output shaft. : Screw the mounting nut ( 12) on to the output shaft counterclockwise and use the combination wrench ( 13) to tighten it down firmly. If the mounting nut is too loose, fit a new one. Removing metal cutting tools : Block the output shaft. : Unscrew the nut clockwise. : Take the parts off the shaft – but do not remove the thrust plate (8). This engine is certified to operate on unleaded gasoline and with the mix ratio 50:1. Your two-stroke engine requires a mixture of high-quality premium gasoline and high-quality two-stroke air- cooled engine oil. Use premium high-quality unleaded gasoline with a minimum octane rating of 89 RON. Note: Models equipped with a catalytic converter require unleaded gasoline. A few tankfuls of leaded gasoline can reduce the efficiency of the catalytic converter by more than 50% . Fuel with a lower octane rating may result in preignition (causing " pinging") which is accompanied by an increase in engine temperature. This, in turn, increases the risk of the piston seizure and damage to the engine. The chemical composition of the fuel is also important. Some fuel additives not only detrimentally affect elastomers (carburetor diaphragms, oil seals, fuel lines etc.), but magnesium castings as well. This could cause running problems or even damage the engine. For this reason it is essential that you use only high-quality fuels! FS 120, FS 200, FS 250 English Fueling Use only STIHL two-stroke engine oil or equivalent high-quality two-stroke air- cooled engine oils for mixing. We recommend STIHL 50:1 two-stroke ...
Dieses Handbuch ist für folgende Modelle:Gartengeräte - 200 (2.54 mb)