Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Troy-Bilt Dateigröße: 2.86 mb Dateiname: Unterrichtssprache:

Retains dog clutch to shaft........... 2 ____ __ DOG CLUTCH — tiller drive shaft..............f: £&$ KEY — 3/16” square x 1 ”, dog clutch to tiller drive shaft ...................... SPRING — dog clutch ................................................ SHIM — dog clutch, 1/16” (.062”) thick.................................... BOLT — hex. hd., 1 /4”-20 x 7/8”, self locking flange.......................... CAP — rear bearing .................................................. GASKET — rear bearing cap .......................................... 1 1 1 3 1 1 11602 9617 9517 1138-1 SHIM — front bearing cap, .010” thick........................................................................Requ SHIM — same as above, .030” thick............................................................................r^u As SHIM — same as above, .005” thick............................................................................Req’d. As SHIM — same as above, .062” thick............................................................................Req’d. BEARING & CUP — tapered cone roller bearing with cup (race). Cone and cup sold as set only........................................................................................................2 SHAFT — main tiller drive. Includes an integral worm gear, plus two pressed-on cone roller bearings, two bearing cups (Ref. #18) and one shoulder washer..........1 SEAL — oil, drive shaft, front......................................................................................1 RETAINING RING — (snap ring), internal. Retains front bearing cup..........................1 WASHER — shoulder (drive shaft).................................................................1 TRANSMISSION HOUSING AND DIPSTICK 23 2206 HOUSING — tiller attachment. Includes pressed-on sleeve in front of housing and one tine shaft bearing cup (Ref. #5) mounted in right side of housing. Empty housing without shafts, gears, seals, dipstick, etc. Call Factory Technical Service Dept, before ordering............................................ 24 2136 DIPSTICK — oil level, tiller attachment................................... Page 13 BOLO TINE ASSEMBLIES (Figure 7) 2 Page 14 BOLO TINE ASSEMBLIES (Figure 7) “"ref. part re- no. NO. DESCRIPTION QTY. PLACES 1 1900871010 TINE HOLDER —welded steel. For left or right side of tiller................... 2 2 9669 BOLT—hexhd,1/2”-20x4-3/4” long .................................... 2 3 9914 LOCKWASHER —1/2”, holder mounting........... .................. 2 4 9952 WASHER — flat. Outerdia. 1.500”, inner dia.. 516”, thickness. 182”.............. 2 5 9301 KEY — tine shaft. 3/16” square x 1” long.................................. 2 6 1270-1A BOLO TINE — single, Left Hand. Used on left and right side tine assemblies. Tine is stamped either “EL” or “AL”. Includes two each Part #9711 bolts, #9913 lockwashers and #9802 hex nuts...................................... 8 7 1270-2A BOLO TINE — single, Right Hand. Used on left and right side tine assemblies. Tine is stamped either “ER” or “AR”. Includes same hardware as described above for left hand tine...................................................... 8 8 9711 BOLT— hex hd,3/8”-16x1”, tine mounting............................... 16 9 9913 LOCKWASHER — 3/8”, tine mounting.................................... 16 10 9802 NUT — hex, 3/8”-16, tine mounting....................................... 16 1901118 TINE REPLACEMENT KIT — unassembled. Includes eight each of Part #1270-1A and #1270-2A tines and sixteen each of #9711 bolts, #9913 lockwashers and #9802 hex nuts. Includes easy-to-follow instructions for installing tines. DOES NOT INCLUDE tine holders, holder mounting hardware, or tine shaft keys...... 1 ... 10355 WELDED STEEL TINE HOLDER REPLACEMENT KIT — Includes one each of Part #2415 welded steel tine holder, #9669 bolt, #9914 lockwasher and #9952 washer. Order two kits if replacing both holders. DOES NOT INCLUDE tines, tine mounting hardware, or tine shaft key................................... 1 CUSTOM TILLING TINES Special hard-faced, high chrome carbon alloy tines that are thicker than standard Bolo Tines. These tines better resist the abrasive action of rocky, gritty, or sandy soil as compared to standard Bolo Tines, and are especially suited for custom tilling or market gardening. 10802 CUSTOM TILLING TINE KIT — Includes eight each of Part #2475-1 and #2475-2 tines and sixteen each of #9711 bolts and #9807 locknuts................... 1 ... 2475-1 BOLO TINE, CUSTOM TILLING —single, left hand.......................... 8 ... 2475-2 BOLO TINE, CUSTOM TILLING —single, right hand......................... 8 9807 LOCKNUT — Hex, 3/8”, used in place of Ref. No.’s 9 and 10 when using Custom Tilling Tines....................................................... 16 FORWARD INTERLOCK SYSTEM (Figure 8) BRIGGS & STRATTON 8 HP KOHLER Page 16 FORWARD INTERLOCK SYSTEM (Figure 8) ^ pgp PART ...

Herunterladen

Geben Sie zwei Ziffern: