Login:
Stimmen - 5, Durchschnittliche Bewertung: 3.8 ( )

Anleitung Shindaiwa, modell C3410

Hersteller: Shindaiwa
Dateigröße: 2.79 mb
Dateiname:
Unterrichtssprache:
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


See Figure 9. 3. Tighten the four socket-head cap screws to secure the cutting attachment shield. CAUTION! Make sure the clamp screw and retaining nut are securely tightened before tightening the four socket-head cap screws. WARNING! NEVER operate the unit without the cutting attachment shield installed and tightly secured! Sub-Shield C3410. (when trimmer head is in use) 1. Attach the shield extension to the cutting attachment shield. See figure 9B. WARNING! NEVER use this machine without sub-shield when using a trimmer head. Sub-shield Hook Hook Receiver Cutting Attachment Shield Figure 9B CAUTION! Make sure the sub-guard is completely hooked at the hook receiver. Assembly (Continued) Handle Bar C3410 Install the handlebar: 1. Use the 4 mm hex wrench to remove the lower cap retaining screws from the handlebar bracket. Remove the cap from the bracket, and note the position of the two 2" long spacers to be installed between the bracket halves. See Figure 5. 2. Position the handle on the outer tube forward of Handle Positioning Label as shown in Figure 5. Reassemble the lower cap to the handlebar bracket in the reverse order of disassembly. 3. Locate the handle in the best position for operator comfort. 4. Firmly tighten both lower cap retaining screws. 5. Secure the cable to the outer pipe with the two bands provided in the tool kit. See Figure 5. Adjustments Adjust Throttle Lever Free Play The throttle lever free play should be approximately 3/16-1/4 inch (4-6 mm). See Figure 6. Make sure that the throttle lever operates smoothly without binding. If it becomes necessary to adjust the lever free play, follow the procedures and illustrations that follow. 3/16-1/4 inch (4-6 mm) Throttle Free Play Figure 6 Handlebar bracket Handle Bar Figure 5 Handle Positioning Label Lower Cap Spacer Spacer Lower Cap Retaining Screws POSITION HANDLE FORWARD OF THIS LINE Bands C3410 1. Loosen the air cleaner cover knob and remove the air cleaner cover. See Figure 7. Cable Adjuster Figure 7 Figure 8 3. Turn the cable adjuster in or out as required to obtain proper free play 3/16-1/4 inch (4-6 mm). See Figure 8. 4. Tighten the locknut. Lock Nut ............ 2. Loosen the lock nut on the cable 5. Reinstall the air cleaner cover. adjuster. See Figure 8. Installing a Trimmer Head NOTE: The C3410 is shipped with Holder A, the blade retainer (safety clip), Holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFT-HAND thread. Remove it by turning CLOCKWISE! 1. With the gear case output shaft facing up, rotate the gearshaft and holder A until the hole in holder A aligns with the matching hole in the gear case flange, and then lock the holder to the gear by inserting the long end of the hex wrench through both holes. See Figure 10. 2. Using the combination spark plug/ screwdriver wrench, remove the shaft bolt and bolt guard. See Figure 10. NOTE: Make sure holder B is installed on the gear- case with the splined hole engaging the gear...

Dieses Handbuch ist für folgende Modelle:
Gartengeräte - 81188 (2.79 mb)
Gartengeräte - 81188 (2.79 mb)
Gartengeräte - 81188 (2.79 mb)
Gartengeräte - 81188 (2.79 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien