Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GC720r Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .LE720r Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . .HS720r Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . .SS725r Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . .TB720r Pole Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBPS Prior to operation, WARNING: read and understand the operator’s manual for unit to be used with this add-on. NOTE: To make installing or removing the add-on easier, place the unit on the ground or on a work bench. NOTE: The extension pole with this unit is to give the user added reach. Follow the directions for removing the add-on or installing the add on to remove or install the extension pole. Removing the add-on 1. Turn the knob counterclockwise to loosen (Fig. 1). 2. Press and hold the release button (Fig. 1). 3. While firmly holding the upper shaft housing, pull the add-on out of the coupler (Fig. 2). Installing the add-on To avoid serious WARNING: personal injury and damage to the unit, shut the unit off before removing or installing add-ons. 1. Remove the hanger from the top of the shaft housing. 2. Turn knob counterclockwise to loosen (Fig. 1). 3. While firmly holding the add-on, push it straight into the coupler (Fig. 2). Coupler Release Button Guide Recess ClockwiseCounterclockwise Knob NOTE: Aligning the release button with the guide recess will help installation (Fig. 1). Primary Hole Upper Shaft Housing Coupler Fig. 2 Lower Shaft Housing Release Button Knob 4. Turn the knob clockwise to tighten (Fig. 3). Lock the release CAUTION: button in the primary hole (Fig. 2) and securely tighten the knob before operating this unit. Knob Fig. 3 The add-ons with the CAUTION: coupler system is to be used in the primary hole only. Using the wrong hole could lead to personal injury or damage to the unit. The add-on should be installed with the release button in the primary hole. Check Flex Shaft Engagement Prior to Using 1. Start the unit. 2. Briefly engage and release the trigger. 3. Check that add-on is operating. 4. If the add-on is not operating, remove add-on and repeat steps for installing the add-on. 5. Recheck operation of add-on attachment. Fig. 1 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS OPERATING PRECAUTIONS Dress properly to reduce the risk of injury when operating this unit. Do not wear loose clothing or jewelry. Wear eye and ear/hearing protection. Wear heavy long pants, boots and gloves. Wear a hard hat. Use a full face shield when needed. WARNING: 1. Keep bystanders 50 feet (15 meters) away when operating the saw. 2. Do not use the pole saw to cut down trees. Use a chain saw without a pole attachment. 3. Grip pole saw securely - one hand on the pole, the other on the handle. 4. Keep finger off the trigger until ready to make cut. 5. Before starting the pole saw, make sure the chain is not touching anything. 6. Keep all parts of your body away from the chain when the saw is running. 7. Do not force the pole saw while cutting. Apply light pressure. It will do the job better and safer at the rate for which it was intended. 8. When cutting limbs or branches that are under tension, use extreme caution. Be alert for wood springing back. When wood tension is released, the limb could spring back and strike operator causing severe injury or death. 9. When carrying pole saw from one place to another: • hold pole at balance point • keep guide bar and chain to the rear 10. Do not cut small brush and saplings with the pole saw. Use a chain saw only, with extreme care. Slender matter may catch in the chain and be whipped toward you. This could also pull you off balance. 11. Never stand directly under the limb you are trimming. Always position yourself out of the path of falling debris (Fig. 4). 12. Never stand on a ladder or other type of unstable support while using the pole saw. 13. Always use both hands to operate pole saw. Keep a firm, steady pressure on the pole saw while cutting, but do not try to force the saw through the wood. 14. Do not use the pole saw to cut limbs larger than 4” (10 cm) in diameter. 15. Keep other persons away from cutting end of pole saw and at a safe distance from work area. (Fig.5). 16. Do not use the pole saw near cable, electric power or telephone lines. Maintain a minimum clearance of 10 feet from all power lines (Fig. 6). Fig. 4 Fig. 5 Fig. 6 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS OPERATING TIPS Avoid kickback. WARNING: Kickback can result in sever in jury or death. See Kickback, page 9, to avoid risk of kickback. Do not operate PoleWARNING: Saw while in a tree, on a ladder or any other unstable work surface, or in any awkward position. You may lose control of Pole Saw causing servere injury. Do not extend arms above shoulders when using Pole Saw. WARNING: Seek professional help if facing conditions beyond your ability. WARNING: Av...