Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Husqvarna Dateigröße: 1006.66 kb Dateiname: HOUS2009_O0907002.pdf Unterrichtssprache:

Remove the spreader and components from carton and place hopper up-side down on a padded surface as shown. Insert ends of leg into handle brace as shown and align holes. Attach brace and leg to frame using (4) 1/4-20 x 2 1/4” hex bolts and locknuts. Drive Wheel 3. Turn spreader upright on wheels. Insert screen into hopper sliding it under the screen clips. Attach the upper handle assembly to handle brace with the handle lever brackets facing as shown. Secure with (4) 1/4-20 x 1 1/2” hex bolts and locknuts. Handle 1/4-20 X 2” Hex Bolt Leg 1/4-20 LOCKNUT Handle Brace 5/32 Dia. x 2. Slide wheels onto end of axle with the 1 1/4” Cotter Pin hub facing toward frame. Wheels are identical to ease assembly. Align the hole in the wheel hub and the hole in the axle as shown. Secure drive wheel to axle with 3/16 Free Turning Wheel dia. x 2” cotter pin. Insert 1/8 dia. x 1 1/4” cotter pin in the hole near the end of axle to retain free turning wheel. Screen Clip Upper Handle Screen 3/16 Dia. x 2” Cotter Pin NOTE POSITION OF LEVER BRACKETS Assembly 1/4-20 X 1 1/2” Hex Bolt 1/4-20 Locknut 4. Slide handle lever between handle brackets as shown and secure with (1) 1/4 dia. clevis pin and 3/32” dia. cotter pin. Make sure lever pivots freely. Install handle grips onto upper handle. Soapy water will ease installation. (Do not use petroleum based products). 1/4 Dia. Clevis Pin 3/32” Dia. Cotter Pin Handle Lever Grip 2 5. Attach control tube to handle lever with (1) 1/4 dia. clevis pin and a 3/32” dia. cotter pin. Slip opposite end of control tube over lower control rod making sure shutoff plate is between the lower rod and the control tube. Secure with a 3/32” dia. cotter pin. Control Tube 1/4 Dia. Clevis Pin 3/32” Dia. Cotter Pin Lower Rod Shutoff Plate Handle Lever 3/32” Dia. Cotter Pin O OOOO P PPPP E EEEE R RRRR A AAAA T TTTT I IIII O OOOO N NNNN 1. Check the product package for the rate setting, and recommended swath width. Loosen rate control knob and slide rate plate to the proper setting. The pattern is controlled by loosening the two knobs on the discharge chute and moving the chute closer or farther away from the impeller (setting A, B, or C). See “PATTERN ADJUSTMENT” for details. 2. Always fill the spreader on the driveway or sidewalk-not on the lawn. Make sure screen is in hopper and spreader is in the “OFF” position. 3. Start spreader moving before opening port. Close before stopping. Always push spreader, never pull. 4. Hold handle so top of spreader is level. Tipping the spreader too far can cause uneven spreading. 5. The settings and swath widths on the product label are recommended starting points. Always check the delivery rate and pattern on a small area before treating a large area. Actual delivery rate can vary due to weather conditions, operating variables, and condition of the product being applied. See “HOW TO DETERMINE SPREADER SETTINGS AND SPREAD WIDTH” for details. USE SWATH WIDTH ON PACKAGE OR ADJUST PER OPERATOR’S WALKING SPEED 6. Push spreader at a normal walking speed 2 1/2 m.p.h. (18 feet in 5 seconds). Apply header strips around area to be treated. Space trips across the area as shown. Keep material off flower beds, sidewalks, etc. 7. When transporting spreader, make sure that it is in the “OFF” position. Make sure handle lever is locked using the hitch pin through the hole in lever. 8. Empty spreader after each use. Return leftover material to its original container. OVERLAP 3 P PPPP A AAAA T TTTT T TTTT E EEEE R RRRR N NNNN A AAAA D DDDD J JJJJ U UUUU S SSSS T TTTT M MMMM E EEEE N NNNN T TTTT Normal spreading of materials requires no adjustment (factory setting “A”) unless stated on the package. In those cases where the spread pattern has shifted, the pattern can be adjusted left and right by loosening the two knobs on the discharge chute and moving the chute closer or farther away from the impeller. Settings of “A, B, and C” are provided as reference. Knob Discharge Chute ImpellerKnob Discharge Chute Settings A simple visual pattern test can be made by operating the spreader over a non-turf area and evaluating the pattern. A more accurate method is to place a row of common, disposable, aluminum cake pans approximately 1 foot on centers. Set the rate plate at a middle setting and make 3 or 4 passes in the same direction as shown. Pour the material collected from each pan into individual bottles of the same size. Set them side by side in order, and visually inspect their volume. If the pattern is not centered (example: volume in bottle #2 left not equal to bottle #2 right), adjust the discharge chute up or down as described in “PATTERN ADJUSTMENT” section. Once the pattern is uniform, the effective pattern width can be determined. The H HHHH O OOOO W WWWW T TTTT O OOOO D DDDD E EEEE T TTTT E EEEE R RRRR M MMMM I IIII N NNNN E EEEE S SSSS P PPPP R RRRR E EEEE A AAAA D DDDD E EEEE R RRRR S SSSS E EEEE T TTTT T TTTT I IIII N NNNN G GGGG S SSSS A AAAA N NNNN D DDDD S SSSS P PPPP R RRRR E EEEE A AAA...

Herunterladen

Geben Sie zwei Ziffern: