Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Husqvarna Dateigröße: 2.42 mb Dateiname: 48ff9133-611a-4398-a725-631ac89d4ad1.pdf Unterrichtssprache:

n Never use a blade near sidewalks, fence posts, buildings or other objects that could cause injury or damage. n Never use a blade for purposes other than those for which it was designed. n Whenever you strike a hard object with a blade, always stop the brushcutter and carefully inspect the blade for damage. NEVER OPERATE THE BRUSHCUTTER WITH A DAMAGED BLADE! n A blade-equipped unit must be equipped with a bicycle-type handlebar or barrier bar as well as a harness or shoulder strap. n Always make sure the cutting attachment shield is properly installed before operating this unit. Operating Units with a Blade The blade rotates counter-clockwise. For best performance and to minimize being stuck by debris, move the blade from right to left while advancing on your work. Position the blade so cuts are made between the blade’s 8 o’clock and 10 o’clock positions (as viewed from above). DO NOT cut between the 10 o’clock and 5 o’clock positions. Cut on the left side of the blade. KEEP YOUR BODY OUTSIDE THE PATH OF BLADE ROTATION Ten O'clock DO NOT CUT Blade Rotation OK To Cut Eight O'clock WARNING! When cutting wood with a saw, feed the blade slowly—never strike or “slam” a spinning blade against the wood. Five O'clock Figure 24 Vertical Cuts Hold the brushcutter with the blade at a 90° angle to the ground so the blade’s bottom edge rotates toward the operator. Move the blade from top to bottom through the cut, and cut only with the bottom edge of the blade. WARNING! DO NOT use 2-tooth or non-Shindaiwa approved 4-tooth cutting blades with Shindaiwa trimmers and brushcutters. Figure 25 WARNING! When making vertical cuts, never allow the blade to exceed waist height. General Maintenance IMPORTANT! MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA CORPORATION THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM. WARNING! Before performing any maintenance, repair or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance work. WARNING! Non-standard parts may not operate properly with your unit and may cause damage and lead to personal injury. NOTE: Using non-standard replacement parts could invalidate your Shindaiwa warranty. Muffler This unit must never be operated with a faulty or missing spark arrester or muffler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss. Spark Plug Keep the spark plug and wire connections tight and clean. Fasteners Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight. Blades Keep blades sharp and check blade condition frequently. If a blade’s performance changes suddenly, stop the engine and check the blade for cracks or other damage. Replace a damaged blade IMMEDIATELY! WARNING! n Never repair a damaged blade by welding, straightening, or by modifying its shape. An altered blade may break during operation, resulting in serious personal injury. n Blades are not interchangeable between Shindaiwa edgers and trimmer/ brushcutter models. Operating any unit with a blade or attachment not approved for that unit can be hazardous and may cause serious injury. Daily Maintenance Prior to each work day, perform the following: n Remove dirt or debris from the engine, check the cooling fins and air cleaner for clogging and clean them as necessary. n Carefully remove any accumulation of dirt or debris from the muffler or the fuel tank. Dirt build-up in these areas could cause engine overheating, induce premature wear, or create a fire hazard. n Check for loose or missing screws or components. Make sure the cutting attachment is securely fastened. n Check the entire unit for leaking fuel or grease. 10-Hour Maintenance Every 10 hours of operation (more frequently in dusty or dirty conditions): Remove the air cleaner element. See Figure 26. Clean or replace as necessary. To clean element: wash it thoroughly in soap and water. Let it dry before reinstalling the element. Unscrew Fastener Remove and clean or replace the element CAUTION! Do not operate the unit if the air cleaner or element is damaged, or if the element is wet. Figure 26 10/15-Hour Maintenance Every 10 to 15 hours of operation: Remove and clean the spark plug. Adjust the spark plug electrode gap to 0.024 - 0.028 inch (0.6 - 0.7 mm). If the spark plug must be replaced, use only an NGK BPMR6A or equivalent resistor type spark plug of the correct heat range. See Figure 27. Clean the spark plug and check the gap at the electrode. 0.024–0.028 inch (0.6–0.7 mm) XST021 CAUTION! Before removing the ...

Herunterladen

Geben Sie zwei Ziffern: