Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
English – 15 ASSEMBLY Fitting other guards and cutting attachments • Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. CAUTION! Ensure that the guard extension is fitted. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram. B A M L H A L C M • Fit the drive disc (B) on the output shaft. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. • Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation. H H • To dismantle, follow the instructions in the reverse order. Adjusting the harness and brush cutter ! WARNING! When using a brush cutter it must always be hooked securely to the harness. Otherwise you will be unable to control the brush cutter safely and this can result in injury to yourself or others. Never use a harness with a defective quick release. Quick release At the front is an easily accessible, quick release. Use this if the engine catches fire or in any other emergency situation that requires you to free yourself from the machine and harness. Spreading the load on your shoulders A well-adjusted harness and machine makes work much easier. Adjust the harness for the best working position. Tension the side straps so that the weight is evenly distributed across both shoulders. 16 – English ASSEMBLY Correct height 1 Forestry clearing Adjust the support strap so that the support hook is around 10 cm below your hip. The blade should be angled forward a little. 2 Grass clearing The support hook should hang around 20 cm below your hip so that the blade is parallel to the ground. Correct balance 1 Forestry clearing Move the suspension ring on the machine forward or backward. It is easier to avoid sawing into the ground if the blade is balanced a few dm above the ground. 2 Grass clearing Let the blade balance at a comfortable cutting height, i.e. close to the ground. English – 17 FUEL HANDLING Fuel safety Never start the machine: 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water. 3 If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines. Transport and storage • Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames, for example, from electrical machinery, electric motors, electrical relays/ switches or boilers. • When storing and transporting fuel always use approved containers intended for this purpose. • When storing the machine for long periods the fuel tank must be emptied. Contact your local petrol station to find out where to dispose of excess fuel. • Ensure the machine is cleaned and that a complete service is carried out before long-term storage. • The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage. • Secure the machine during transport. ! WARNING! Take care when handling fuel. Bear in mind the risk of fire, explosion and inhaling fumes. Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. ! WARNING! Fuel and fuel fumes are highly inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin. For this reason observe caution when handling fuel and make sure there is adequate ventilation. Petrol CAUTION! Always use a quality petrol/oil mixture at least 90 octane (RON). If your machine is equipped with a catalytic converter (see chapter on Technical data) always use a good quality unleaded petrol/oil mixture. Leaded petrol will destroy the catalytic converter. Use low-emission petrol, also known as alkylate petrol, if it is available. • The lowest octane recommended is 90 (RON). If you run the engine on a lower octane grade than 90 so- called knocking can occur. This gives rise to a high engine temperature, which can result in serious engine damage. • When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two-stroke engines. • Never use two-stroke oil intended for water-cooled engines, s...