Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
The Chain should not be adjusted too tightly, since it does have to be able to move. When properly adjusted, the Chain should be able to be pulled, using light force, about 1/4” away from the Guide Bar and snap back without sagging. Replace the Plastic Cover before use. Assembling the Telescopic Pole. Connect Aluminum Tube 1 (45) and Aluminum Tube 2 (52) with Connector 1 (46). Secure Plastic Coupling 1A (48) and Plastic Coupling 2A (51) with Screws (43), and Nuts (8, 47). Fasten with Locking Knob (50) Connect Aluminum Tube 2 (52) and Aluminum Tube 3 (57) with Connector 2 (53). Secure Plastic Coupling 1B (55) and Plastic Coupling 2B (56) with Screws (43), and Nuts (8, 47). Fasten with Locking Knob (50). Functions The Telescoping Pole Saw is designed to trim branches on trees. Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. General operating instructions Turn the Power Switch of the tool to the “OFF” position and unplug the tool from the electrical outlet before assembling or making any adjustments to the tool. Maintain a proper grip on the Pole Saw whenever it is running. Hold the tool with both hands. Always keep your left hand on the Front Handle (61) and your right hand on the Rear Handle (74, 86), so that your body is to the left of the Pole Saw. Never use a left-handed (cross-handed) grip or any stance which would place your body or arm across the chain line. Always wear the Shoulder Strap (66) to properly support the Pole Saw when moving or using unit. To activate the Saw, push the Safety Switch (72) forward and depress the Power Switch (75). Allow the Saw Chain to cut for you. Exert only light downward pressure. If you attempt to force the cut, damage to the Guard Bar, Chain, or Motor can result. Do not use a back and forth sawing type motion for cutting. Release the Power Switch as soon as the cut is completed. Running the Pole Saw for long periods without a pause can cause unnecessary wear or damage to the Guard Bar, Chain, and Motor. Beware Kickback! Never cut with tip of blade. Cut longer branches down in sections for greater efficiency and safety. (See example below.) Safety Switch (72) Power Switch (75) Power Cord (88) Safety Switch (72) Power Switch (75) Power Cord (88) IMPORTANT: After running the Pole Saw for an extended period of time, allow the Engine to idle for several minutes to dissipate heat. This will prevent the Pole Saw from being damaged by overheating. To prevent accidents, turn off the tool and disconnect from the power supply after use. Clean the Pole Saw, then store the tool indoors out of children’s reach. Maintenance And Servicing Risk of serious personal injury from accidental starting or electric shock. Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. Damaged equipment can fail, causing serious personal injury. Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, maintenance, and lubrication BEFORE EACH USE, inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. After Use, clean external surfaces of the tool with clean, moist cloth. After each use, remove the Plastic Cover (34) and clean oil and sawdust out of the area underneath, especially the recess of the Chain Tension Screw (40) and oil duct, with a damp cloth or compressed air to extend the life of the Pole Saw. WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. Any repairs not specifically covered in this manual MUST be completed by a qualified service professional. Troubleshooting Problem Possible Causes Probable Solutions Pole Saw will not start No power at outlet. Cord not connected. Check power at outlet. Check that cord is plugged in. Pole Saw runs, but will not cut Chain is placed backwards on Guide Bar Remove Chain and reattach correctly Pole Saw only cuts when forced. Cutting yields only sawdust and large chips Chain is dull. Have Chain sharpened by a professional sharpening service. Oil DuctChain Tension Screw (40) Oil DuctChain Tension Screw (40) Problem Possible Causes Probable Solutions Pole Saw runs slowly and stalls easily Power supply receiving low voltage. Extension cord wire size is too small. Pole Saw does not run when Power Switch is depressed. Safety Switch not depressed enough to release Power Switch. Extension cord connections are loose. Open line fuse or circuit breaker fault. Open wiring circuit on saw. Press Safety Lock in before squeezing Power Switch. Cord cord connections. Check line fuse and circuit breaker. Have the Pole Saw...