Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
– While keeping the engine level, remove the oil gauge, and confirm that the oil is filled within the upper and lower limit marks. When the oil is in short in such a way that the oil gauge touches the oil only by its tip, in particular with the oil gauge remaining inserted in the crankcase without screwing-in (Fig. 1), refill new oil near the port (Fig. 2). – For reference, the oil refill time is about 10h (10 times or 10 tanks of oil refill). – If the oil changes in color or mixes with dirt, replace it with new one. (For the interval and method of replacement, refer to P 17) Recommended oil: SAE 10W-30 oil of API Classification, Class SF or higher (4-stroke engine for automobile) Oil volume: Approx. 0.08L Note: If the engine is not kept upright, oil may go into around the engine, and may be refilled excessively. If the oil is filled above the limit, the oil may be contaminated or may catch fire with white. Point 1 in Replacement of Oil “Oil Gauge” – Remove dust or dirt near the oil refill port, and detach the oil gauge. – Keep the detached oil gauge free of sand or dust. Otherwise, any sand or dust adhering to the oil gauge may cause irregular oil circulation or wear on the engine parts, which will result in troubles. – As an example to keep the oil gauge clean, it is recommended to insert the oil gauge on its knob side into the engine cover, as shown in Fig.3. If oil adheres around this tip, refill new oil. Upper limit (Edge of oil refill port) Fig.1 Fig.2 Oil gauge Fig.3 11 (1) Keep the engine level, and detach the oil gauge. (2) Fill oil up to the edge of the oil refill port. (Refer to Fig.2 of the preceding page). Feed oil with the lubricant refill container. (3) Securely tighten the oil gauge. Insufficient tightening may cause oil leakage. Point 2 in Replacement of Oil: “If oil spills out” – If oil spills out between the fuel tank and engine main unit, the oil is sucked into through the cooling air intake port, which will contaminate the engine. Be sure to wipe out spilt oil before start of operation. REFUELING Handling of Fuel It is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be performed in a sufficiently ventilated room or in the open air. Never inhale fuel vapor, and keep fuel away from you. If you touch fuel repeatedly or for a long time, the skin becomes dry, which may cause skin disease or allergy. If fuel enters into the eye, clean the eye with fresh water. If your eye remains still irritated, consult your doctor. Storage Period of Fuel Fuel should be used up within a period of 4 weeks, even if it is kept in a special container in a well-ventilated shade. If a special container is not used or if the container is not covered, fuel may deteriorate in one day. STORAGEOF MACHINEAND REFILLTANK-Keep the machine and tank at a cool place free from direct sunshine. -Never keep the fuel in the cabin or trunk. Fuel The engine is a four-stroke engine. Be sure to use an automobile gasoline (regular gasoline or premium gasoline). Points for Fuel – Never use a gasoline mixture which contains engine oil. Otherwise, it will cause excessive carbon accumulation or mechanical troubles. – Use of deteriorated oil will cause irregular startup. Refueling WARNING: INFLAMMABLES STRICTLY PROHIBITED Gasoline used: Automobile gasoline (unleaded gasoline) – Loosen the tank cap a little so that there will be no difference in atmospheric pressure. – Detach the tank cap, and refuel, discharging air by tilting the fuel tank so that the refuel port will be oriented upward. (Never refill fuel full to the oil refill port.) – Wipe well the periphery of the tank cap to prevent foreign matter from entering into the fuel tank. – After refueling, securely tighten the tank cap. . If there is any flaw or damage on the tank cap, replace it. . The tank cap is consumable, and therefore should be renewed every two to three years. Fuel tank cap Fuel upper limit Fuel tank 12 CORRECT HANDLING OF MACHINE CORRECT HANDLING OF MACHINE Attachment of shoulder strap – Adjust the strap length so that the cutter blade will be kept parallel with the ground. Detachment For MS-251.4 – In an emergency, push the notches (1) at both sides, and you can detach the machine from you. Be extremely careful to maintain control of the machine at this time. Do not allow the machine to be deflected toward you or anyone in the work vicinity. WARNING: Failure to maintain complete control of the machine at all could result in serious bodily injury or DEATH. For MS-250.4 – In case of emergency, remove the emergency detachment lever (2) by pulling strongly with a finger. The machine sill detach from body. Be extremely careful to maintain control of the machine at this time. Do not allow the machine to be deflected toward you or anyone in the work vicinity. WARNING: Failure to maintain complete control of the machine at all could result in serious bodily injury or DEATH. Hanger (2) Hanger POINTS IN OPERATION AND...